SETTINGSÊMENU
SENSITIVITY:
1.0v
,
1.2v
,
1.4v
,
2.0v
(Vrms)
Sets the overall level required from your source to the INPUT XLR to reach maximum volume. The factory setting is 1.4v.
A lower setting will increase volume, a higher setting will decrease volume.
CONTOUR EQ:
(Available in SINGLE and DUAL cabinet presets)
EQ contours:
Live 1, Live 2, Playback1, Playback2
The Contour EQ setting offers four different equalization presets. The preset names are based on the type of material to be played,
however select which one sounds best for your music. The factory flat setting is “
Live 1
”. (see the contour curves in the chart below)
ENHANCE BASS: (
Available in SINGLE and DUAL cabinet FullRange presets):
Off, On
The Enhance Bass feature allows lower frequencies to be reproduced by the VELA™, creating a virtual subwoofer at lower volumes.
Low frequency response is extended by 15Hz and boosts the 50-80Hz range. The effect will be reduced at the highest volumes to
stay within the limits of the system but still adds depth at less than maximum levels. (see the BassEnhance curve in the chart below)
TRx3810A Block Diagram
TRx3810A v1.2b
Sensitivity: 1.4v
TRx3810A Contour:
Live 1
TRx3810A Preset:
Single FullRange
Carvin
TRx3810A
TRx3810A
Enhance Bass: Off
back to the
welcome screen
TRx3810A v1.2b
Sensitivity: 1.4v
TRx3810A Contour:
Live 1
TRx3810A Preset:
Single ExtSub85Hz
TRx3810A v1.2b
Sensitivity: 1.4v
TRx3810A Contour:
Live 1
TRx3810A Preset:
Dual FullRange
TRx3810A
Enhance Bass: Off
back to the
welcome screen
TRx3810A v1.2b
Sensitivity: 1.4v
TRx3810A Contour:
Live 1
TRx3810A Preset:
Dual ExtSub85Hz
back to the
welcome screen
TRx3810A v1.2b
Sensitivity: 1.4v
TRx3810A Preset:
3-4 Full-Range
back to the
welcome screen
TRx3810A v1.2b
Sensitivity: 1.4v
TRx3810A Preset:
3-4 Ext Sub 85Hz
back to the
welcome screen
back to the
welcome screen
(welcome screen)
Select one of the
6 presets
Set the Sensitivity
within each preset
Choose a Contour
in Single or Dual presets:
Set Enhance Bass On or Off
in Single or Dual FullRange:
To select which screen is shown, use the LEFT and RIGHT buttons
t
u
.
Use the UP and DOWN buttons
pq
to change the Preset or to change the value of the settings shown in grey.
Settings are automatically saved within each Preset.
Contour curve presets (DSP output)
TRx3810A Preset screen:
This selection will load different settings for the TRx3810A - VELA™. These settings are optimized for the number of VELA™ cabinets
to be linked in a single column and if there will be subwoofers as part of the system. The ExtSub85Hz settings add a 85Hz high pass
filter to allow more efficient power from the VELA™ when adding subs to the system. Set subwoofer crossovers to 85Hz (low pass).
Single FullRange:
One cabinet per side, no subwoofers in system. Full range.
SingleExtSub85Hz:
One cabinet per side, when using subwoofers. 85Hz, 24dB/oct. Butterworth high pass filter.
Dual FullRange:
Two cabinets per side, no subwoofers in system. Full range.
Dual ExtSub85Hz:
Two cabinets per side, when using subwoofers. 85Hz, 24dB/oct. Butterworth high pass filter.
3-4 Full-Range:
3-4 cabinets per side, no subwoofers in the system. Full range.
3-4 Ext Sub 85Hz:
3-4 cabinets per side, when using subwoofers. 85Hz, 24dB/oct. Butterworth high pass filter.
