NOTE:
Warranty does not cover burned out drivers caused by excessive power or distortion, or physical damage caused by general use, moisture or dust.
CAUTION:
Square wave distortion from power amps can destroy drivers much faster than clean power.
SCx1112 specs
System Type: 12-inch 2-Way, Bass-reflex
Frequency Response:
60 Hz – 20 kHz (-10DB)
70 Hz – 18 kHz (-3 dB)
Coverage Pattern: Monitor 60x90; Main 90x60
Crossover: 2-Way with Speaker Guard™ HF protection
Crossover Frequency: 1.8 k Hz (internal)
Recommended external crossover frequency:
1.8k Hz @ 12dB/oct. or greater
Power: Continuous / Program / Peak
Full Range 300w /600w /1200w
Recommended Amplifier Power: 300 to 900w
Sensitivity (1w @ 1m): 96dB
Maximum SPL: 120dB Cont. / 126dB Peak
LF Driver: 12-inch woofer
HF Driver: 1-inch exit Mylar 1.75-inch VC
Connectors: Two 4-pin Twist-Loc connectors
Two 1/4-inch connectors
Nominal Impedance full range: 8 ohms
Bi-amp LF: 8 ohms 300w /600w /1200w
Bi-amp HF: 8 ohms 60w /120w /240w
Enclosure: 13-Ply Premium Russian Baltic Birch
Suspension/Mounting: 1-3/8-inch pole mount cup
Finish: Black DuraTex™
Transport: 1 Recessed Handle
Grill: Black powder coated 16-Ga steel
Dimensions (H x W x D):
16.5 in x 15.25 in x 22.5 in
420 mm x 388 mm x 572 mm
Net Wt: 36.5 lb (16.5 kg)
SCx1115 specs
System Type: 15-inch 2-Way, bass-reflex
Frequency Response: 54 Hz – 20 kHz (-10DB)
62 Hz – 18 kHz (-3 dB)
Coverage Pattern: 90H x 60V
Crossover: 2-Way with Speaker Guard™ HF protection
Crossover Frequency: 1.8 k Hz (internal)
Recommended external crossover frequency:
1.8k Hz @ 12dB/oct. or greater
Power: Continuous / Program / Peak
Full Range 400w /800w /1600w
Recommended Amplifier Power: 400 to 1000w
Sensitivity (1w @ 1m): 98dB
Maximum SPL: 124dB Cont. / 130dB Peak
LF Driver: 15-inch Heavy Duty 2.5-inch VC
HF Driver: 1-inch exit Mylar 1.75-inch VC
Connectors: Two 4-pin Twist-Loc connectors
Two 1/4-inch connectors
Nominal Impedance full range: 8 ohms
Bi-amp LF: 8 ohms 400w /800w /1600w
Bi-amp HF: 8 ohms 60w /120w /240w
Enclosure: 13-Ply Premium Russian Baltic Birch
Suspension/Mounting: 1-3/8-inch pole mount cup
Finish: Black DuraTex™
Transport: 2 Recessed Handles
Grill: Black powder coated steel
Dimensions (H x W x D):
25.75 in x 18.5 in x 14.5 in
654 mm x 470 mm x 367 mm
Net Wt: 45 lb (20.5 kg)
SCx1253 specs
System Type: Dual 15-inch 3-Way, Co-planar bass reflex
Frequency Response:
50 Hz – 20 kHz (-10DB)
60 Hz – 18 kHz (-3 dB)
Coverage Pattern: 90H x 60V
Crossover: 3-Way with Speaker Guard™ HF protection
Crossover Frequencies: 350 Hz, 2.0 kHz (internal)
Recommended external crossover frequency:
350 Hz @ 12dB/oct. or greater
Power: Continuous / Program / Peak
Full Range 800w /1600w /3200w
Recommended Amplifier Power: 500 to 1600w
Sensitivity (1w @ 1m): 101dB 60-350Hz; 98dB 350-18KHz
Maximum SPL: 128dB Cont. / 134dB Peak
LF Driver: Dual 15-inch Heavy Duty 2.5-inch VC
MF Driver: 6.5-inch Heavy Duty 1.5-inch VC
HF Driver: 1-inch exit Mylar 1.75-inch VC
Connectors: Two 4-pin Twist-Loc connectors
Two 1/4-inch connectors
Nominal Impedance full range: 4 ohms
Bi-amp LF: 4 ohms 800w /1600w /3200w
Bi-amp MF/HF: 8 ohms 150w /300w /600w
Enclosure: 13-Ply Premium Russian Baltic Birch
Finish: Black DuraTex™
Transport: 2 Recessed Handles
Grill: Black powder coated steel
Dimensions (H x W x D):
29 in x 19.75 in x 22.75 in
737 mm x 505 mm x 580 mm
Net Wt: 88.2 lb (40 kg)
SCx1118 specs
System Type: 18-inch Sub, bass-reflex
Frequency Response:
35 Hz – 1.5K Hz (-10DB)
40 Hz – 1k Hz (-3 dB)
Coverage Pattern: omni
Crossover: 200Hz (internal)
Recommended external crossover frequency:
80-120 Hz @ 12dB/oct.
Power: Continuous / Program / Peak
Full Range 500w /1000w /2000w
Recommended Amplifier Power: 500 to 1000w
Sensitivity (1w @ 1m): 97dB
Maximum SPL: 123dB Cont. / 130dB Peak
LF Driver: 18-inch, 3-inch VC, woofer
Connectors: Two 4-pin Twist-Loc connectors
Two 1/4-inch connectors
Nominal Impedance: 8 ohms
Enclosure: 13-Ply Russian Baltic Birch
Suspension/Mounting: Top: 1 x 1-3/8-inch Pole Cup
foot receivers for SCx1253
Finish: Black DuraTex™
Transport: 2 Recessed Handles
Grill: Black powder coated steel
Dimensions (H x W x D):
23.5 in x 19.75 in x 22.75 in
600 mm x 505 mm x 580 mm
Net Wt: 65 lb (29.5 kg)
SCx1118A specs:
same as SCX1118 except:
Power Amp: 700w RMS continuous/1400w Peak
THD: < 0.05% @90%, 0.1% @full power
Crossover: Active, 24dB/oct. @80 or 120 Hz
Protection systems:
short circuit, thermal, Speaker Guard
™
protection
Power Requirement: 120/240VAC, 50/60HZ, 600VA
Net Wt: 66 lb (30 kg)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
pOWer SOurCeS: The SCx1118a should be connected to a power supply only of the type described in the operating
instructions or as marked on the unit. unplug during lightning storms.
grOunDIng Or pOlarIZaTIOn: precautions should be taken so that the grounding or polarization means of an appliance is
not defeated.
pOWer COrD: power supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs and the point where they exit from the appliance. The plug
or power inlet is the disconnect device and shall remain readily operable.
plaCemenT: Do not block ventilation openings. Do not install near heat sources such as radiators, stoves or other products
that produce heat. Do not install in a confined area. use only mounting hardware such as brackets and tripods recommended
by the manufacturer.
fuSIng: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. refer to replacement text on the
unit for correct fuse type.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
LIMITED WARRANTY
Your Carvin SCx is guaranteed against failure for 5 YearS, except for failure due to overpowering or
normal wear and tear. Carvin will service and supply all parts at no charge to the customer providing the
unit is under warranty. Shipping costs are the responsibility of the customer. CarVIn DOeS nOT paY fOr
parTS Or SerVICIng OTHer THan Our OWn. a COpY Of THe OrIgInal InVOICe IS reQuIreD TO
VerIfY YOur WarranTY. This warranty does not cover, and no l iability is assumed, for damage due to:
natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow
instructions. This warranty is in lieu of all other warranties, expressed or implied. no representative or
person is authorized to represent or assume for Carvin any liability in connection with the sale or servicing
of Carvin products.
SERVICE
In the uSa, please go to www.carvinservice.com.
Outside the uSa, contact your dealer or go to http://www.carvinworld.com for your nearest service center.
Include a written description of the problem with serial number and date of purchase.
HELP SECTION
1) unIT WIll nOT Turn On: Check the power to the aC cord. Check for tripped circuit breakers,
unplugged extension cords or power-strip switches that may be turned off. Check the fuse or circuit
breaker on the unit if available. If the fuse has been replaced with the proper value and the fuse fails again,
or the internal circuit breaker activates after reset, the unit will require servicing.
2) nO OuTpuT with pOWer light On: Shipping damage will be the primary reason for your product to not
function properly. please give us a call to help you determine the problem.
3) Keep YOur unIT lOOKIng neW: use only a dry cloth to wipe the control and venting areas. Surfaces
without openings may be cleaned with a damp cloth.
THIS UNIT CONTAINS HIGH VOLTAGE INSIDE!
REFER SERVICING TO A QUALIFIED TECHNICIAN
CAUTION
