HELPFUL HINTS:
If more bass is wanted overall, turn up the LEVEL on the
S610B subwoofer instead of turning up the LOW controls
on the S600B.
This will prevent the limiter in the S600B from engaging
early. Adjustments can still be made to each S600B channel.
NO SOUND FROM SUBWOOFER
:
- Check the POWER LED and battery indicator LED.
- Check the XLR connection:
The LINE IN of the S610B subwoofer connects to the LINE OUT
of the S600B (or other source).
- The S600B “LINK TO MAIN” switch should be set to IN.
POOR BASS RESPONSE
:
- Increase the LEVEL setting on the S610B subwoofer to the
middle “S600” range.
Some systems may require a higher
setting.
- On the S600B Stagemate™, set each channel’s LOW frequency
control to the middle “0” setting and adjust for each input.
Channels not providing bass content (such as vocal mics) can
be set lower.
- The placement of the subwoofer in the room can cause cancel-
lations at low frequency. Try moving the subwoofer a few feet,
or to the other side of the setup.
TOO MUCH BASS
:
- Reduce the LEVEL setting on the S610B subwoofer to the middle
“S600” range. Some systems may require a lower setting.
- On the S600B Stagemate™, set each channel’s LOW frequency
control to the middle “0” setting and adjust for each input.
FOR MAXIMUM OUTPUT
:
- Avoid blocking the front of the subwoofer with instrument
cases, stage props or other items which can absorb or reflect
sound.
- If the LEVEL is set very high, it may cause the protection
circuits to limit the output. Start with the LEVEL within the
center “S600” range and increase by small amounts.
- Add a second S610B subwoofer. If you are using the S600B
with more than one S648 extention or two S600B’s, a second
S610B sub may be needed to match the required level.
CONNECTING THE
S610B SUBWOOFER TO THE
S600B STAGEMATE
™
PA MIXER
1. Connect an XLR cable to the LINE OUT XLR of
the S600B
StageMate
™
2. On the S600B, press IN the LINK TO MAIN
switch located just to the left of the LINE OUT
connector.
3. Connect the other end of the XLR cable to one
of the LINE IN inputs on the S610B
subwoofer
.
USING THE SYSTEM:
1. On the S610B
subwoofer
adjust the LEVEL
control, adding enough bass to match the volume
of the S600B
StageMate
™.
2. Control the volume of the whole system with
the MAIN control on the S600B
StageMate
™.
POLE MOUNTING THE
S600B AND S648
ON THE S610B SUBWOOFER
1. Find a solid, level surface to place the S610B, preferably
out of high traffic areas. Stack a second S610B if desired.
2. Screw in a threaded pole (M20t) on top of the S610B
subwoofer. (Adjust SS50T pole to proper length, see below)
3. Place the S600B on the standard pole end.
4. Using an SS3 short pole, one S648 extension can be
secured on top of the S600B or S648.
-Maximum recommended height is 6-1/2 ft.(2m), or
with 2 subwoofers up to 7ft (2.15m) only on solid flooring.
-Typical pole length settings:
(1) S610B sub, S600B = 48in. (1.2m)
(1) S610B sub, S600B+S648 (or two S648) =36in. (0.9m)
(2) S610B subs, S600B+S648 = <30in. (0.75m)
CAUTION:
As with any pole mounted setup, avoid placing it directly
next to busy walkways, on dance floors, or use in windy
conditions.
Do not place the stacked system on uneven surfaces, loose
sand or rocky ground.
If the stack is unsteady, use seperate tripod pole stands for
the S600B and/or S648.
Do not stack more than two S600B or S648 on the pole
mounted in the S610B subwoofer.
MAX HEIGHT: 7 ft. (2.15m)
w/2 subs, only on solid flooring
SS50T pole set to ~36in. (0.9m)
SS50T pole set set to minimum
~30in. (0.75m)
SS3 (SHORT POLE INSERT)
REQUIRED
S600B ON BOTT
OM
S600B ON BOTT
OM
SHORT STACK FOR
ELEVATED STAGES
CAN STAND
ON SIDE
WHEN USING
SEPERATE
STANDS FOR
S600B/S648
THREADED
END (M20t)
MAX HEIGHT:
6-1/2 ft. (2m)
THREADED POLE END
