CARVIN ENGINEERING DATA
VLD1
STEVE VAI LEGACY DRIVE
STEVE VAI LEGACY DRIVE
PG.
3
VLD1 SPECIFICATIONS:
»
Preamp Tubes: Two 12AX7 (dual stage)
»
Controls: MASTER, BYPASS
»
Drive channel: VOLUME, DRIVE, BASS, MID, TREBLE,
PRESENCE, GAIN switch
»
Clean channel: VOLUME, BASS, MID, TREBLE,
PRESENCE switch
»
Footswitches: BYPASS, GAIN, DRIVE/CLEAN
»
1/4” Footswitch jack: Tip: Hi Gain, Ring: Drive/Clean
»
1/4” Bypass jack: Tip: Bypass
»
Bypass type: Hardwire bypass, relay engaged
»
Phones/Cab Voiced Out: G3 speaker cabinet voicing,
stereo or mono, low impedance capable
76-32311A 011117
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!
THIS UNIT CONTAINS HIGH VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
EXAMPLE SETUPS
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the unit.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or
polarization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the unit beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
This symbol is intended to alert
the user to the presence of unin-
sulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient mag-
nitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and main-
tenance (servicing) instructions
in the literature accompanying
the appliance.
LIMITED WARRANTY
Your Carvin preamp is guaranteed against failure for ONE YEAR (USA) unless otherwise stated.
Vacuum tubes are guaranteed for 90 days. Carvin will service and supply all parts at no charge
to the customer providing the unit is under warranty. Shipping costs are the responsibility of the
customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN.
A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin
assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty does
not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss
of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is
in lieu of all other warranties, expressed or implied. No representative or person is authorized to
represent or assume for Carvin any liability in connection with the sale or servicing of Carvin prod-
ucts. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
MAINTAINING YOUR EQUIPMENT
The outer surface of your unit can be wiped with a dry or slightly damp cloth in order to remove
dust and bring back the new look. Avoid spilling liquids or allowing any other foreign matter inside
the unit. As with all pro gear, avoid prolonged use in caustic environments (salt air). When used
in such an environment, be sure the equipment is adequately protected.
SERVICE:
In the USA: email: [email protected], or visit our website: www.carvinaudio.com and under
“SUPPORT” click on “REPAIR INFORMATION”
Outside the USA: contact your dealer, or go to http://www.carvinaudio.com click on “DEALERS”
for your nearest service center.
Include a written description of the problem with serial number and date of purchase.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
EFFECTS LOOP
RETURN
The Legacy DRIVE is designed to feed
nearly any power amp stage to drive guitar
speaker cabinets with the Legacy sound. If
you already have a favorite guitar amp and
want to add a new sound, the Legacy DRIVE
also works as a pedal into the front of your
amp with a true hardwire bypass. Even if
you are playing without an amp, Carvin’s 3rd
generation analog Cabinet Voicing circuit will
emulate the frequency response of a guitar
speaker cabinet. Connect headphones for
“silent” practice, or feed to any combina-
tion of effects, recording inputs, or live PA
gear to capture Legacy tones without micing
guitar speakers.
»
DC adapter (included): 12VDC/1A voltage regulated,
5.5mmOD/2.1mmID Center Positive
»
Size: H x W x D 3.825” x 8.875” x 8.375” (97mm x
225mm x 213mm)
»
Weight (without adapter): 3.4 lb. (1.55 kg)
»
Warranty: One Year, 90 days on tubes
EXAMPLE SETUPS
The Legacy DRIVE is designed to feed
nearly any power amp stage to drive
guitar speaker cabinets with the Legacy
sound. If you already have a favorite
guitar amp and want to add a new
sound, the Legacy DRIVE also works as
a pedal into the front of your amp with
a true hardwire bypass. Even if you are
playing without an amp, Carvin Amp’s 3rd
generation analog Cabinet Voicing circuit
will emulate the frequency response
of a guitar speaker cabinet. Connect
headphones for “silent” practice, or feed
to any combination of effects, recording
inputs, or live PA gear to capture Legacy
tones without miking guitar speakers.
