CARVIN KB100 Operating Manual Download Page 4

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SAFETY INSTRUCTIONS (EUROPEAN)

The conductors in the AC power cord are colored in accordance with the following code.

GREEN & YELLOW—Earth        BLUE—Neutral         BROWN—Live

U.K. MAIN PLUG WARNING:  A molded main plug that has been cut off from the cord is unsafe.
NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT
MAIN PLUG INTO A POWER SOCKET.

IMPORTANT!  FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE:  Appliance should not be used near water (near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool, etc).  Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES:  The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION:  Precautions should be taken so that the grounding or polariza-
tion means of an appliance is not defeated.
POWER CORD PROTECTION:  Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING:  The user should not attempt to service the appliance beyond that described in the oper-
ating instructions.  All other servicing should be referred to qualified service personnel.
FUSING:  If your unit is equipped with a fuse receptacle, replace only with the same type fuse.  Refer
to replacement text on the unit for correct fuse type.

REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL! THIS UNIT CON-
TAINS HIGH VOLTAGE INSIDE!

CAUTION

RISK OF ELECTRIC SHOCK

REPLACEMENT PARTS LIST 

(for circuit cards)

This symbol is intended to alert
the user to the presence of
uninsulated “dangerous volt-
age” within the product’s enclo-

sure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

This symbol is intended
to alert the user to the
presence of important
operating and mainte-
nance (servicing) instructions in the
literature accompanying the appliance.

LIMITED WARRANTY

Your Carvin product is guaranteed against failure for ONE YEAR unless otherwise stated.  Carvin will

service and supply all parts at no charge to the customer providing the unit is under warranty.  Shipping
costs are the responsibility of the customer.  CARVIN DOES NOT PAY FOR PARTS OR SERVICING
OTHER THAN OUR OWN.   A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WAR-
RANTY.  Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This
warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents,
abuse, loss of parts,  lack of reasonable care, incorrect use, or failure to follow instructions.  This war-
ranty is in lieu of all other warranties, expressed or implied. No representative or person is authorized
to represent or assume for Carvin any liability in connection with the sale or servicing of Carvin prod-
ucts. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. 

SERVICE

In  the USA, please call 800-235-2235 for a RMA # (return authorization number).  Write this number on

the box and enclose a description of the problem.  Prepay to Carvin 12340 World Trade Drive, SD, CA   92128.

Outside the USA, contact your dealer or go to http://www.carvinworld.com for your nearest service center.

Include a written description of the problem with serial number and date of purchase. 

HELP SECTION

1)  AMP WILL NOT TURN ON

Check the power to the amp.  Check for tripped circuit breakers, unplugged extension cords or
power-strip switches that may be turned off.  After you have verified there is AC power and the
amp still doesn’t work, your unit will require servicing.

2)  MAINTENANCE

To bring back the new look, your KB100 front panel can be wiped with mild detergent and/or a
warm damp soft cloth.  This will remove normal dust and oil from the cabinet. Never spray clean-
ers or detergents directly at the electronic controls.  The KB100 is virtually sealed from outside
dust and dirt, but it is recommended to keep the unit free from excessive dust, dirt, and moisture
as much as possible. 

80-71004A

PCB ASSY MAIN KB100 SMT

03-00475

1  EACH  SPACER PAD .1X .4X .75 W/ADHSV
SPACER UNDER PL1

03-49553

4  EACH  TAPE W/ADHSVE 3M .375 X .375

03-50135

1  EACH  STANDOFF LED .500 X .135 T1, D1

03-60043

1  EACH  SIL PAD W/ADHESIVE 9 MIL
STICK TO VP1

05-22102

“6  EACH  POLYOLEFIN SHRINK TUBING 1/16”””

06-40050

3  EACH  TERMINAL VERT MALE PC MTG .250
“QC1, QC2, QC3”

06-40060

3  EACH  TERMINAL 90dg MALE PC MTG .250
“QC4, QC5, QC6”

15-00300

2  EACH  INDUCTOR .3 mH DRUM CORE
“L7, L8”

15-27430

4  EACH  BEAD W/LEAD .138Dx .35Lx 22AWG
“L1, L2, L5, L6”

15-05001

1  EACH  LINE FILTER/INDUCTOR 5mH 3A, L3

15-90032G

1  EACH  TRANSFORMER SWITCHING 100W ,T1

21-31100

1  EACH  RECEPTACLE AC W/FAST-ON CHASS
PL1

21-40000

1  EACH  XLR FEMALE CONNECTOR W/O GRND
J41

21-40020

1  EACH  JACK RCA DUAL PC VERTICAL MTG
J13

21-51345

1  EACH  JACK .250 PHONE MONO PLASTIC, J5

21-52345

10  EACH  JACK .250 PHONE MONO STEEL
“J1, J2, J3, J6,”
“J11, J12, J21, J22, J31, J41”

21-52545

2  EACH  JACK .250 PHONE STEREO STEEL
“J4, J10”

23-03529

2  EACH  FUSEHOLDER CLIPS 3AG VERT MTG, F1

23-11004

2  EACH  CONNECT HEADER 4 PIN STRAIGHT
“H4A, H4B”

23-11008

2  EACH  CONNECT HEADER 8 PIN STRAIGHT
“H1A, H1B”

23-11010

4  EACH  CONNECT HEADER 10 PIN STRAIGHT
“H2A, H2B”
“H3A, H3B”

25-02201

1 *  STD 4  EACH  ASSEMBLED SWITCH AND CAP
“S11, S21, S31, S32”

30-71004B

1  EACH  PCB MAIN KB100

41-27322

3  EACH  CAP POLY FILM .027uF 250VAC 10
“C113, C114, C115”

41-47322-

1 1  EACH  CAP MYLR .0470UF 250VAC BOX
C41

41-47422

1  EACH  CAP MYLR .47uF 250VAC BOX
C122

42-12142

1  EACH  CAP ELEC 120MFD  400VOLT 20%
C27

45-18152

1  EACH  CAP CERM 180PF  500VOLT 5%
C90

45-33113

1  EACH  CAP CERM 330PF 1000VOLT 10%
C40

47-10225

“2  EACH  CAP ELEC 1,000 MFD  25V 20%”
“C38, C39”

47-22151

1  EACH  CAP ELEC 220 MFD  50VOLT 10%
C31

47-47151

4  EACH  CAP ELEC 470 MFD 50 VOLT 20%
“C42, C43, C44, C45”

49-10050

1  EACH  CAP SMT 1UF 50V ELECTROLITIC

C15

49-10212

1  EACH  0.001UF SMT 10% FILM 0805 50V
C61

49-10312

6  EACH  0.01UF SMT 10% FILM 080550V
“C33, C64, C93, C95, C104, C76”

49-10451

9  EACH  0.1 uF SMT 10% FILM 1206 50V
“C23, C32, C70, C72,”
“C67, C68, C69, C110, C134”

49-22035

33  EACH  SMT CAP 22uF 35v ELECTROLITIC
“C1, C2, C3, C4, C6,”
“C8, C9, C14, C17, C19,”
“C20, C21, C22, C26, C34,”
“C35, C46, C47, C51, C54,”
“C55, C56, C59, C62, C91,”
“C100, C102, C107, C108, C111,”
“C303, C304, C310”

49-22212

3  EACH  0.0022UF SMT 10% FILM 0805 50V
“C75, C78, C106”

49-22312

1  EACH  0.022UF SMT 10% FILM 0805 50V
C60

49-25152

3  EACH  220PF SMT 5% CERAMIC 0805
“C92, C139, C79”

49-33312

2  EACH  0.033UF SMT 10% FILM 0805  50V
“C116, C71”

49-39052

25  EACH  39PF SMT 5% CERAMIC 0805
“C5, C7, C10, C11, C16,”
“C18, C24, C25, C29, C48,”
“C49, C50, C52, C53, C57,”
“C58, C66, C97, C99, C101,”
“C128, C309, C403, C80, C133”

49-47212

3  EACH  0.0047uF SMT FILM 0805 50V
“C30, C63, C73”

49-47312

3  EACH  0.047UF SMT 10% FILM 0805  50V
“C12, C13, C74”

49-56152

3  EACH  560PF SMT 5% CERAMIC 0805
“C77, C305, C306”

49-82052

2  EACH  82PF SMT 5% CERAMIC 0805
“C103, C127”

51-00050

“2  EACH  RES   0.00 OHM .50X.20”” JUMPER”
“B5, B7”

53-47045

1  EACH  RES  47.00KOHM 1.00W 5% CARBON
R42

55-04705

2  EACH  RES    .47 OHM  5W 10% SB VERT
“R113, R114”

58-00035

4  EACH  0.0 SMT JUMPER 1206
“B3, R51, R58, R59”

58-10015

3  EACH  10.5 SMT .25W 1206 1%
“R127, R128, R41”

58-10025

4  EACH  100.5 SMT .25W 1206 1%
“R47, R92, R112, R164”

58-10035

10  EACH  1K SMT .25W 1206 1%
“R25, R111,”
“R84, R150, R63, R64,”
“R101, R102, R3, R133”

58-10045

33  EACH  10K SMT .25W 1206 1%
“R2, R22, R24, R4, R10,”
“R17, R35, R57, R61, R65,”
“R80, R81, R87, R135, R136,”
“R55, R60, R119, R90, R148, R82,”
“R153, R312, R108, R98,”

“R111, R120, R121, R125,”
“R134, R535, R37, R137”

58-10055

4  EACH  100K SMT .25W 1206 1%
“R77, R79, R69, R36”

58-10065

3  EACH  1M SMT .25W 1206 1%
“R166, R168, R93”

58-15035

6  EACH  1.5K SMT .25W 1206 1%
“R58, R59, R66, R86,”
“R304, R305”

58-15045

7  EACH  15K SMT .25W 1206 1%
“R3, R12, R34, R19, R26,”
“R122, R99”

58-15055

3  EACH  150K SMT .25W 1206 1%
“R71, R75, R147”

58-22035

14  EACH  2.2K SMT .25W 1206 1%

“R306, R307, R97,”
“R70, R72, R74, R76, R78, R96,”
“R106, R109, R110, R116, R123”

58-22045

19  EACH  22K SMT .25W 1206 1%
“R8, R11, R13, R27, R28,”
“R29, R44, R52, R67, R94,”
“R5, R6, R18, R146,”
“R115, R100, R105, R126, R132”

58-27025

1  EACH  274 OHM SMT .25W 1206 1%
R50

58-33045

7  EACH  33K SMT .25W 1206 1%
“R7, R9, R20, R23, R48, R537, R43”

58-36055

1  EACH  365K SMT .25W 1206 1%
R73

58-39035

2  EACH  3.9K SMT .25W 1206 1%
“R40, R54”

58-47015

2  EACH  47.5 SMT .25W 1206 1%
“R85, R151”

58-47025

2  EACH  470.5 SMT .25W 1206 1%
“R104, R158”

58-47035

3  EACH  4.7K SMT .25W 1206 1%
“R62, R95,”
“R91,”

58-47045

18  EACH  47K SMT .25W 1206 1%
“R38, R39, R56, R88, R89, R32, R33,”
“R15, R21, R68, R83, R149,”
“R103, R107, R129, R117, R118, R124”

58-56035

5  EACH  5.6K SMT .25W 1206 1%
“R14, R16, R30, R31”
R1

58-68025

1  EACH  680  SMT  .25W 1206 1%
R49

58-68035

2  EACH  6.8K SMT .25W 1206 1%
“R25, R53”

58-68045

1  EACH  68K SMT .25W 1206 1%
R132

58-91025

2  EACH  910.5 SMT .25W 1206 1%
“R45, R46”

60-00083

1  EACH  TRANSISTOR 15A 100V NPN
Q1

60-00084

1  EACH  TRANSISTOR 15A 100V PNP
Q12

60-20060

1  EACH  TRANSIENT VOLT SUPP 200V 600W
Z1

60-22100

1  EACH  IC PRIMARY VIPER 100
VP1

60-25011

1  EACH  IC OPTO COUPLER ISOLATOR
OP2

60-40002

1  EACH  THERMISTOR 40ohm 2amp 20%
TR1

61-47430

1  EACH  DIODE ZNR REG 1N4743A 13V 1W
Z2

60-50200

4  EACH  DIODE GEN REC 1N5402 3A 200V
“D14, D15, D16, D17”

60-55500

2  EACH  TRANS 2N5550 HV NPN 250V T0-92
“Q2, Q11”

60-75330

1  EACH  LED GREEN DIFFUSED 3MM T-1.00
D1

60-78150-

1 *    STD  1  EACH  REG VOLT 15+V 1A (PREPPED)
Q16

60-79150-

1 *    STD 1  EACH  REG VOLT 15-V 1A (PREPPED)
Q17

60-80200

2  EACH  DIODE 8A 200V TO-220
“D22, D23”

61-04737

1  EACH  DIODE REG GEN 1N4737A 7.5V 1W
Z4

62-04739

3  EACH  SMT DIODE ZENER 4739
“Z8, Z9, Z10”

62-08451

1  EACH  SMT ZENER DIODE 5.1 VOLT
Z501

62-06001

3  EACH  DIODE ULTRA FAST 600V 1A SMA
“D18, D19, D21”

62-19140

13  EACH  1N914 HI SPD SMT 250mW DIODE
“D2, D3, D5, D6, D9, D10, D11,”
“D12, D13, D20, D27, D28, D29”

62-20430

3  EACH  NJM2043SMT(TESTED) DUAL HFREQ
“A5, A11, A12”

62-45650

14  EACH  NJM4565 SMT DUAL HI FREQ
“A1, A2, A3, A4, A6,”
“A7, A8, A9, A10, A14,”
“A15, A16, A17, A19”

62-54001

9  EACH  MMBT5401LT1 PNP SOT-23 SMT
“Q3, Q4, Q5, Q6, Q9, Q10, Q12, Q14,”Q18

62-55500

5  EACH  MMBT5550 NPN SOT-23
“Q1, Q7, Q8, Q13, Q19”

70-05710

1  EACH  RELAY SPDT 12A@120VAC/24V COIL
K1

70-21050

1  EACH  FUSE ABC  5.00A FAST 6.35X32MM
F1

71-09252D

“4  EACH  POT 9 “”D-P”” 25F B50K-CC BLUE”
“P32, P42, P43, P44”

71-09253B

“3  EACH  POT 9 “”D-P”” 25F B50K WHITE”
“P31, P41, P1”

71-10320

5  EACH  FADER 20MM SL20V3-B10K-L15D(G)
“P51, P52, P53, P54, P55”

72-12552

“2  EACH  POT 12 “”D-P”” 25F 1B50Kx2-C BLK”
“P12, P22”

72-12553

“4  EACH  POT 12 “”D-P”” 25F 1B50Kx2 BLACK”
“P11, P21, P2, P3”

Summary of Contents for KB100

Page 1: ...ounter clockwise Adjust all BAL and EQ tone controls to their center detent position Turn the KB100 on by the power switch on the front panel and watch for the power LED to come on Adjust the volume controls to the desired playing level For detail on the individual channel tone controls and the graphic equalizer see the appropriate sections in this manual CARVIN ENGINEERING DATA OPERATING MANUAL K...

Page 2: ...R connector is wired as per the industry standard pin 1 is ground pin 2 is positive and pin 3 is negative The 1 4 jack is designed for key board and line level signals Both of these inputs can be used at the same time 12 LO MID AND HI TONE CONTROLS The LO MID and HI tone controls are used to shape the bass midrange and treble sound of the input signal It is suggested that the tone control settings...

Page 3: ...nds the 112AG extension speaker 24 AC POWER The detachable AC POWER CORD supplied is designed to operate with one type of voltage the European 230V export model uses a CEE 7 plug cord set Make sure the cord is securely inserted into the back of the unit Plug the cord into a grounded 3 prong power source No attempt should ever be made to defeat or use the amp without the ground connected The intern...

Page 4: ... JACK 250 PHONE MONO STEEL J1 J2 J3 J6 J11 J12 J21 J22 J31 J41 21 52545 2 EACH JACK 250 PHONE STEREO STEEL J4 J10 23 03529 2 EACH FUSEHOLDER CLIPS 3AG VERT MTG F1 23 11004 2 EACH CONNECT HEADER 4 PIN STRAIGHT H4A H4B 23 11008 2 EACH CONNECT HEADER 8 PIN STRAIGHT H1A H1B 23 11010 4 EACH CONNECT HEADER 10 PIN STRAIGHT H2A H2B H3A H3B 25 02201 1 STD 4 EACH ASSEMBLED SWITCH AND CAP S11 S21 S31 S32 30 ...

Reviews: