TYPICAL SINGLE MONITOR MIX SETUP
120V 60Hz Slow Blow
FUSE 8A 3AG 700VA
www.carvin.com
MADE
A
U S
INTHE
SERIAL NUMBER
8 OHMS/CH
4 OHMS/CH
2 OHMS/CH
8
Ω
BRIDGED
4
Ω
BRIDGED
175W
250W
375W
500W
750W
INPUTS
1
2
MONO
BRIDGE
—
+
+
—
OUTPUTS
1 2
PARALLEL
INPUTS
LIMITER
XLR
GND
LIFT
CH1
PIN 2
PIN 3 SIGNAL –
PIN 1 GND
The channel PARALLEL switch OFF (OUT).
25V or 70V
Distribution System:
Wattage of transformer (TAP)
divided by total wattage
of Amp = Number of
transformer/speaker(s)
that can be hooked up.
or
To signal socket XLR or 1/4" 2 or 3 cond. shielded
Activate the BRIDGE switch
(IN). Control the level by Ch 1
( Ch 2 does not function.
Ch 1 Input
+
16
8
4
C
or
Single speaker or
system connected
in BRIDGE mode.
Minimum imp. 4
Ω
15w
7w
3w
1w
C
+
16
8
4
C
15w
7w
3w
1w
C
120V 60Hz Slow Blow
FUSE 8A 3AG 700VA
www.carvin.com
MADE
A
U S
INTHE
SERIAL NUMBER
INPUTS
1
2
MONO
BRIDGE
—
+
+
—
OUTPUTS
1 2
PARALLEL
INPUTS
LIMITER
XLR
GND
LIFT
CH1
PIN 2
PIN 3 SIGNAL –
PIN 1 GND
For single input operation, push
the PARALLEL button IN.
From Mixer Monitor Output
BRIDGE switch
must be OFF (OUT).
or
Up to four monitors per side using 8 ohm systems
or two monitors per side with 4 ohm systems.
25V OR 70V DISTRIBUTION SYSTEM
* For monural (mono) systems, depress the PARALLEL button (IN) and use only CHANNEL 1 input (speaker
hookup identical to stereo). Mono is normally recommended for live stage applications. Live stereo sounds
great in the center of the audience, however, the audience on one side will not hear the program material pre-
sented on the other side.
SHIELD
+POS.
2
1
3
-NEG.
SHIELD
+POS.
2
1
3
-NEG.
SHIELD (GROUND)
+ SIGNAL (BAL.)
- SIGNAL (BAL.)
BALANCED MIC/LINE
SPEAKER OR SIGNAL LINE CABLE
INTERRUPT (PATCH)/STEREO OR BALANCED SIGNAL LINE
(Shielded)
(Unshielded)
(Shielded)
(Shielded)
SHIELD (GROUND)
+ SIGNAL (REC.)
- SIGNAL (SEND)
RING
SLEEVE
SLEEVE RING TIP
TIP
SHIELD (GROUND)
+ TIP (POS. SIGNAL)
SLEEVE
SLEEVE
TIP
TIP
2
3
120V 60Hz Slow Blow
FUSE 8A 3AG 700VA
www.carvin.com
MADE
A
U S
INTHE
SERIAL NUMBER
INPUTS
1
2
MONO
BRIDGE
—
+
+
—
OUTPUTS
1 2
PARALLEL
INPUTS
LIMITER
XLR
GND
LIFT
CH1
PIN 2
PIN 3 SIGNAL –
PIN 1 GND
From Mixer Monitor 1 Output
BRIDGE switch
must be OFF (OUT).
or
For dual monitor mix (stereo), the PARALLEL
switch must be in the OUT position (OFF).
From Mixer Monitor 2 Output
Up to four monitors per side using 8 ohm systems
or two monitors per side with 4 ohm systems.
TYPICAL DUAL MONITOR MIX SETUP