15
Fig. 24 — Mounting Position for Field Disconnects
(up to 100A)
Field power wires are connected to the unit at line-side
pressure lugs at the main terminal block (TB1) or at factory-
installed option non-fused disconnect switch or HACR, or
field-installed or factory-installed Single Point box for elec-
tric heat. Refer to Table 3 for maximum wire size at connec-
tion lugs. Use copper wire only. See Fig. 25.
Table 3 — Connection Lug Min/Max Wire Sizes
NOTE: TEST LEADS — Unit may be equipped with short
leads (pigtails) on the field line connection points off the optional
non-fused disconnect switch or HACR. These leads are for fac-
tory run-test purposes only; remove and discard before connect-
ing field power wires to unit connection points. Make field pow-
er connections directly to line connection pressure lugs only.
Fig. 25 — Power Wiring Connections
Minimum
Maximum
TB1 in unit control box
#14
#1
Terminal/Fuse block in Single
Point Box for Electric Heat
#8
3/0
80A Disconnect Option
#14
#4
100A Disconnect Option
#8
1/0
200A Disconnect Option
#4
300 kcmil
25A HACR Option
#14
1/0
30A HACR Option
#14
1/0
35A HACR Option
#14
1/0
40A HACR Option
#14
1/0
50A HACR Option
#14
1/0
60A HACR Option
#14
1/0
70A HACR Option
#14
1/0
80A HACR Option
#14
1/0
90A HACR Option
#14
1/0
100A HACR Option
#14
1/0
110A HACR Option
#4
300 kcmil
125A HACR Option
#4
300 kcmil
150A HACR Option
#4
300 kcmil
175A HACR Option
#4
300 kcmil
200A HACR Option
#4
300 kcmil
WARNING
FIRE HAZARD
Failure to follow this warning could result in intermittent
operation or performance satisfaction.
Do not connect aluminum wire between disconnect switch
and unit. Use only copper wire.
Units Without Single Point Box, Disconnect or HACR Option
Units With Disconnect or HACR Option
L1
L2
L3
2
4
6
1
5
Optional
Disconnect
Switch
or HACR
Disconnect factory test leads; discard.
Factory
Wiring
3
Equip GR Lug
Ground
(GR)
Units With Electric Heat Option with Single Point Box
and Without Disconnect or HACR Option
L1
L2
L3
Single Point Box
Factory
Wiring
Equip GR
Lug
Ground (GR)
Terminal Block
— OR —
L1
L2
L3
Single Point Box
Factory
Wiring
Equip GR
Lug
Ground (GR)
Fuse/Terminal Block
Fuse
Fuse
Fuse
Disconnect
per
NEC
11
12
13
L1
L2
L3
TB1
208/230-3-60
460-3-60
575-3-60
Ground
(GR)
Equip
GR Lug
Summary of Contents for WeatherMaster 50HC14
