Carrier WeatherMaker 50TCQA07 Installation Instructions Manual Download Page 31

Page: 31 / 48

Remote Occupancy

The remote occupancy accessory is a field--installed

accessory. This accessory overrides the unoccupied mode

and puts the unit in occupied mode. When installing this

accessory, the unit must be configured for remote

occupancy by setting

MENU

→

Config

→

Inputs

→

input 3,

5, 8, or 9

to Remote Occupancy and normally open (N/O)

or normally closed (N/C).
Also set

MENU

→

Schedules

→

occupancy source

to DI

on/off. Input 8 or 9 is recommended for easy of

installation. Refer to Fig. 47 and Table 8 for wire

terminations at J5.

Power Exhaust (output)

Connect the accessory Power Exhaust contactor coil(s) per

Fig. 55.

Power Exhaust

J11-3

TAN

GRA

PEC

CTB

THERMOSTAT

C08464

Fig. 55 -- RTU--MP Power Exhaust Connections

Space Relative Humidity Sensor -- The RH sensor is not

used with 50TCQ models at this time.

Communication Wiring -- Protocols

General

Protocols are the communication languages spoken by

control devices. The main purpose of a protocol is to

communicate information in the most efficient method

possible. Different protocols exist to provide different

kinds of information for different applications. In the BAS

application, many different protocols are used, depending

on manufacturer. Protocols do not change the function of

a controller; just make the front end user different.
The RTU--MP can be set to communicate on four different

protocols: BACnet, Modbus, N2, and LonWorks. Switch 3

(SW3) on the board is used to set protocol and baud rate.

Switches 1 and 2 (SW1 and SW2) are used to set the

board’s network address. See Fig. 56 for the switch setting

per protocol. The 3rd party connection to the RTU--MP is

through plug J19.

NOTE

: Power must be cycled after changing the SW1--3

switch settings.
Refer to the

RTU--MP 3rd Party Integration Guide

for

more detailed information on protocols, 3rd party wiring,

and networking.

SW3 Protocol Selection

PROTOCOL

DS8

DS7

DS6

DS5

DS4

DS3

DS2

DS1

BACnet MS/TP

(Master)

Unused

OFF

Select Baud Select Baud

Modbus

(Slave)

Unused

OFF

Select Baud Select Baud

(Slave)

Unused

OFF

LonWorks

Unused

OFF

NOTE:
DS = Dip Switch
BACnet MS/TP SW3 example shown

Baud Rate Selections

BAUD RATE

DS2

DS1

9600

OFF

19,200

OFF

38,400

OFF

76,800

C07166

Fig. 56 -- RTU--MP SW3 Dip Switch Settings

50TC

Summary of Contents for WeatherMaker 50TCQA07

















































Search results

Summary of Contents for WeatherMaker 50TCQA07

Reviews:

Carrier WeatherMaker 50TCQA07, Installation Instructions Manual, Page: 31 / 48

Search results

Summary of Contents for WeatherMaker 50TCQA07

Reviews: