background image

RGAP(A,B)XX: Installation and User Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

9

TROUBLESHOOTING

The Return Air Purifier is equipped with a power indicator light located

on the door (

Fig. 21

). This power indicator light will illuminate when the

Return Air  Purifier  door  is  installed,  the  power  switch  is  in  the  ON

position, AND the furnace blower is running.
Refer  to 

(ERROR  and  STATUS  CODES  on p10)

  for  troubleshooting

procedures.

A11370

Fig. 22 – Removal of Deposits from Ionization Pins

CAUTION

!

SAFETY HAZARD

Failure  to  follow  this  caution  may  result  in  personal  injury  or

equipment damage.
The following instructions are for use by qualified personnel only.

WARNING

!

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury or death.

The  following  procedures  will  expose  electrical  components.

Disconnect  power  between  checks  and  proceed  carefully.  Only  a

trained, experienced service person should install and/or troubleshoot

the Return Air Purifier.

Top View

30°

POINTS ARE SHARP! BE VERY CAREFUL DURING CLEANING.

Tip of point with residue

Tip of point after cleaning

Summary of Contents for RGAP Series













Reviews: