Carrier PG95ESU User Manual Download

Page: 19 / 58

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

The furnace can be installed horizontally in an attic or crawlspace on

either the left-hand (LH) or right-hand (RH) side. The furnace can be

hung from floor joists, rafters or trusses or installed on a

non-combustible platform, blocks, bricks or pad.

A11237

Fig. 31 – Furnace Pitch Requirements

Platform Furnace Support

Construct working platform at location where all required furnace

clearances are met. (

Table 1

and

Fig. 32

) For furnaces with 1-in. (25

mm) clearance requirement on side, set furnace on non-combustible

blocks, bricks or angle iron. For crawlspace installations, if the furnace

is not suspended from the floor joists, the ground underneath furnace

must be level and the furnace set on blocks or bricks. Condensate Trap

section for required and recommended clearances for trap installation

(see

Fig. 6

Fig. 21

, and

Fig. 32

Suspended Furnace Support

The furnace must be supported under the entire length of the furnace

with threaded rod and angle iron (see

Fig. 33

). Secure angle iron to

bottom of furnace as shown.

Roll-Out Protection

Provide a minimum 12-in. x 22-in. (305 x 559 mm) piece of sheet metal

for flame roll-out protection in front of burner area for furnaces closer

than 12-in. (305 mm) above the combustible deck or suspended furnaces

closer than 12-in. (305 mm) to joists. The sheet metal MUST extend

underneath the furnace casing by 1-in. (25 mm) with the door removed.
The bottom closure panel on furnaces of widths 17-1/2-in. (445 mm) and

larger may be used for flame roll-out protection when bottom of furnace

is used for return air connection.

A200088

Fig. 32 – Working Platform for Attic Installation

NOTE:

Furnace shown is a direct vent application. Refer to the venting

section for allowable vent configurations.

NOTE:

N Coil only, add 8-in. separation between coil and furnace for

all other unshielded coils. (See evaporator coil spacer or shield

requirements.)

NOTE:

Local codes may require a drain pan and condensate trap when a

condensing furnace is installed over a finished ceiling.

A200085

Fig. 33 – Suspended Furnace Installation

NOTE:

Furnace shown is a direct vent application. Refer to the venting

section for allowable vent configurations.

NOTE:

N Coil only, add 8-in. separation between coil and furnace for

all other unshielded coils. (See evaporator coil spacer or shield

requirements.)

NOTE:

Local codes may require a drain pan and condensate trap when a

condensing furnace is installed over a finished ceiling.

Supply Air Connections

For a furnace not equipped with a cooling coil, the outlet duct shall be

provided with a removable access panel. This opening shall be

accessible when the furnace is installed and shall be of such a size that

CAUTION

MINOR PROPERTY HAZARD

Failure to follow this caution may result in minor property damage.
Local codes may require a drain pan under entire furnace and

condensate trap when a condensing furnace is used in an attic

application or over a finished ceiling.

LEVEL 0-IN. (0 MM) TO
1/2-IN. (13 MM) MAX

UPFLOW OR
DOWNFLOW

HORIZONTAL

MIN 1/4-IN. (6 MM) TO
1/2-IN. (13 MM) MAX

ADDITIONAL 1” CLEARANCE BELOW TRAP RECOMMENDED

FOR SERVICE

6-3/8” CLEARANCE

NEEDED FOR TRAP

NOTE

: FURNACE SHOWN IS A DIRECT VENT APPLICATION. REFER TO THE

VENTING SECTION FOR ALLOWABLE VENT CONFIGURATIONS.

NOTE

COIL

ONLY,

ADD

SEPARATION

BETWEEN

COIL

FURNACE

FOR

ALL

OTHER

UNSHIELDED

COILS)

SEE EVAPORATOR COIL SPACER OR

SHIELD REQUIREMENTS.

6-3/8” CLEARANCE

NEEDED FOR TRAP

ADDITIONAL 1”

CLEARANCE BELOW TRAP

RECOMMENDED

FOR SERVICE

Summary of Contents for PG95ESU



























































Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands

Carrier PG95ESU, User Manual

Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands