manualshive.com logo in svg

Carrier Gemini 38AU07 Series, Installation Instructions Manual

Share
Download
Carrier Gemini 38AU07 Series Installation Instructions Manual Download Page 15

15

Fig. 13 — Power Wiring Connections

CONVENIENCE OUTLETS

Two types of convenience outlets are offered on 38AU

models: Non-powered and unit-powered. Both types provide

a 125-volt GFCI (ground-fault circuit-interrupter) duplex re-

ceptacle rated at 15-A behind a hinged waterproof access

cover, located on the end panel of the unit. See Fig. 14.

Non-Powered Type

This type requires the field installation of a general-pur-

pose 125-volt 15-A circuit powered from a source elsewhere

in the building. Observe national and local codes when select-

ing wire size, fuse or breaker requirements and disconnect

switch size and location. Route 125-v power supply conduc-

tors into the bottom of the utility box containing the duplex

receptacle. Maximum continuous current for this type of con-

venience outlet (non-unit powered) must not exceed 8 Amps.

Unit-Powered Type

A unit-mounted transformer is factory-installed to step

down the main power supply voltage to the unit to 115-v at

the duplex receptacle. This option also includes a manual

switch with fuse, located in a utility box and mounted on a

bracket behind the convenience outlet; access is through the

unit’s control box access panel. See Fig. 14.

The primary leads to the convenience outlet transformer are

not factory-connected. Selection of primary power source is a

customer-option. If local codes permit, the transformer primary

leads can be connected at the line-side terminals on the unit-

mounted non-fused disconnect or HACR breaker switch; this

will provide service power to the unit when the unit disconnect

switch or HACR switch is open. Other connection methods will

result in the convenience outlet circuit being de-energized when

the unit disconnect or HACR switch is open. See Fig. 15.

Fig. 14 — Convenience Outlet Location

Fig. 15 — Powered Convenience Outlet Wiring

The unit-powered convenience outlet has a 1000 VA rated

transformer. Maximum continuous current must not exceed

8 Amps.

Test the GFCI receptacle by pressing the TEST button on

the face of the receptacle to trip and open the receptacle. Check

for proper grounding wires and power line phasing if the GFCI

receptacle does not trip as required. Press the RESET button to

clear the tripped condition.

Fuse on power type: The factory fuse is a Bussman

1

“Fusetron” T-15, non-renewable screw-in (Edison base) type

plug fuse.

WARNING

ELECTRICAL OPERATION HAZARD
Failure to follow this warning could result in personal injury

or death.
Units with convenience outlet circuits may use multiple dis-

connects. Check convenience outlet for power status before

opening unit for service. Locate its disconnect switch, if

appropriate, and open it. Tag-out this switch, if necessary.

11

1

3

L1

L2

L

3

C

TB1

20

8

/2

3

0-

3

-60

460-

3

-60

575-

3

-60

Unit

s

 Witho

u

t Di

s

connect Option

Unit

s

 With Di

s

connect Option

2

4

6

1

3

5

L1

L2

L

3

Option

a

l

Di

s

connect

S

witch

Di

s

connect f

a

ctory te

s

t le

a

d

s

; di

s

c

a

rd.

F

a

ctory

Wiring

Di

s

connect

per

NEC

1. Bussmann and Fusetron are trademarks of Cooper Technologics

Company.

Control Box

Access Panel

Pwd-CO

Transformer

Convenience

Outlet

GFCI

Pwd-CO

Fuse 

Switch

UNIT

VOLTAGE

CONNECT

AS

PRIMARY

CONNECTIONS

TRANSFORMER

TERMINALS

208,
230

240

L1: RED + YEL
L2: BLU + GRA

H1 + H3
H2 + H4

460

480

L1: RED
Splice BLU + YEL
L2: GRA

H1

H2 + H3

H4

575

600

L1: RED
L2: GRA

H1
H2

Summary of Contents for Gemini 38AU07 Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands