Carrier Flotronic II 30GN040 Operating And Troubleshooting Manual Download

Page: 58 / 72

Table 17 — Thermistor Temperature (°F) vs Resistance/Voltage Drop; Flotronic™ II

TEMPERATURE

VOLTAGE

RESISTANCE

(F)

DROP (V)

(OHMS)

−25.0

4.821

98010

−24.0

4.818

94707

−23.0

4.814

91522

−22.0

4.806

88449

−21.0

4.800

85486

−20.0

4.793

82627

−19.0

4.786

79871

−18.0

4.779

77212

−17.0

4.772

74648

−16.0

4.764

72175

−15.0

4.757

69790

−14.0

4.749

67490

−13.0

4.740

65272

−12.0

4.734

63133

−11.0

4.724

61070

−10.0

4.715

59081

−9.0

4.705

57162

−8.0

4.696

55311

−7.0

4.688

53526

−6.0

4.676

51804

−5.0

4.666

50143

−4.0

4.657

48541

−3.0

4.648

46996

−2.0

4.636

45505

−1.0

4.624

44066

0.0

4.613

42679

1.0

4.602

41339

2.0

4.592

40047

3.0

4.579

38800

4.0

4.567

37596

5.0

4.554

36435

6.0

4.540

35313

7.0

4.527

34231

8.0

4.514

33185

9.0

4.501

32176

10.0

4.487

31202

11.0

4.472

30260

12.0

4.457

29351

13.0

4.442

28473

14.0

4.427

27624

15.0

4.413

26804

16.0

4.397

26011

17.0

4.381

25245

18.0

4.366

24505

19.0

4.348

23789

20.0

4.330

23096

21.0

4.313

22427

22.0

4.295

21779

23.0

4.278

21153

24.0

4.258

20547

25.0

4.241

19960

26.0

4.223

19393

27.0

4.202

18843

28.0

4.184

18311

29.0

4.165

17796

30.0

4.145

17297

31.0

4.125

16814

32.0

4.103

16346

33.0

4.082

15892

34.0

4.059

15453

35.0

4.037

15027

36.0

4.017

14614

37.0

3.994

14214

38.0

3.968

13826

39.0

3.948

13449

40.0

3.927

13084

41.0

3.902

12730

42.0

3.878

12387

43.0

3.854

12053

44.0

3.828

11730

45.0

3.805

11416

46.0

3.781

11112

47.0

3.757

10816

48.0

3.729

10529

49.0

3.705

10250

50.0

3.679

9979

51.0

3.653

9717

52.0

3.627

9461

53.0

3.600

9213

54.0

3.575

8973

55.0

3.547

8739

56.0

3.520

8511

57.0

3.493

8291

58.0

3.464

8076

59.0

3.437

7868

60.0

3.409

7665

61.0

3.382

7468

62.0

3.353

7277

63.0

3.323

7091

64.0

3.295

6911

65.0

3.267

6735

66.0

3.238

6564

67.0

3.210

6399

68.0

3.181

6238

69.0

3.152

6081

70.0

3.123

5929

TEMPERATURE

VOLTAGE

RESISTANCE

(F)

DROP (V)

(OHMS)

3.093

5781

3.064

5637

3.034

5497

3.005

5361

2.977

5229

2.947

5101

2.917

4976

2.884

4855

2.857

4737

2.827

4622

2.797

4511

2.766

4403

2.738

4298

2.708

4196

2.679

4096

2.650

4000

2.622

3906

2.593

3814

2.563

3726

2.533

3640

2.505

3556

2.476

3474

2.447

3395

2.417

3318

2.388

3243

2.360

3170

2.332

3099

2.305

3031

2.277

2964

100

2.251

2898

101

2.217

2835

102

2.189

2773

103

2.162

2713

104

2.136

2655

105

2.107

2597

106

2.080

2542

107

2.053

2488

108

2.028

2436

109

2.001

2385

110

1.973

2335

111

1.946

2286

112

1.919

2239

113

1.897

2192

114

1.870

2147

115

1.846

2103

116

1.822

2060

117

1.792

2018

118

1.771

1977

119

1.748

1937

120

1.724

1898

121

1.702

1860

122

1.676

1822

123

1.653

1786

124

1.630

1750

125

1.607

1715

126

1.585

1680

127

1.562

1647

128

1.538

1614

129

1.517

1582

130

1.496

1550

131

1.474

1519

132

1.453

1489

133

1.431

1459

134

1.408

1430

135

1.389

1401

136

1.369

1373

137

1.348

1345

138

1.327

1318

139

1.308

1291

140

1.291

1265

141

1.289

1240

142

1.269

1214

143

1.250

1190

144

1.230

1165

145

1.211

1141

146

1.192

1118

147

1.173

1095

148

1.155

1072

149

1.136

1050

150

1.118

1029

151

1.100

1007

152

1.082

986

153

1.064

965

154

1.047

945

155

1.029

925

156

1.012

906

157

0.995

887

158

0.978

868

159

0.962

850

160

0.945

832

161

0.929

815

162

0.914

798

163

0.898

782

164

0.883

765

165

0.868

750

166

0.853

734

TEMPERATURE

VOLTAGE

RESISTANCE

(F)

DROP (V)

(OHMS)

167

0.838

719

168

0.824

705

169

0.810

690

170

0.797

677

171

0.783

663

172

0.770

650

173

0.758

638

174

0.745

626

175

0.734

614

176

0.722

602

177

0.710

591

178

0.700

581

179

0.689

570

180

0.678

561

181

0.668

551

182

0.659

542

183

0.649

533

184

0.640

524

185

0.632

516

186

0.623

508

187

0.615

501

188

0.607

494

189

0.600

487

190

0.592

480

191

0.585

473

192

0.579

467

193

0.572

461

194

0.566

456

195

0.560

450

196

0.554

445

197

0.548

439

198

0.542

434

199

0.537

429

200

0.531

424

201

0.526

419

202

0.520

415

203

0.515

410

204

0.510

405

205

0.505

401

206

0.499

396

207

0.494

391

208

0.488

386

209

0.483

382

210

0.477

377

211

0.471

372

212

0.465

367

213

0.459

361

214

0.453

356

215

0.446

350

216

0.439

344

217

0.432

338

218

0.425

332

219

0.417

325

220

0.409

318

221

0.401

311

222

0.393

304

223

0.384

297

224

0.375

289

225

0.366

282

Summary of Contents for Flotronic II 30GN040









































































Search results

Summary of Contents for Flotronic II 30GN040

Reviews:

Related manuals for Flotronic II 30GN040

Brands by name

Popular brands

Carrier Flotronic II 30GN040, Operating And Troubleshooting Manual

Search results

Summary of Contents for Flotronic II 30GN040

Reviews:

Related manuals for Flotronic II 30GN040

Brands by name

Popular brands