background image

8

Fig. 18 — EconoMi$erX Hood Detail

27. After powering unit controller, program the W7220 controller 

per the instructions to follow. See Programming the W7220 

Controller section on page 12 for summarized controller set-

up instructions. After all settings have been made, re-install 
the unit control box panel. (See Fig. 9.)

28. Install the filter by opening the filter clips which are located 

underneath the hood top. Insert the aluminum filter into the 
bottom filter rack (hood divider). Push the filter into position 

past the open filter clips. Close the filter clips to lock the filter 

into place. (See Fig. 18.)

Economizer performance charts are shown in Fig. 19 and 20. See 

base unit installation manual to make adjustments to meet building 

ventilation requirements.

Fig. 19 — Barometric Relief Flow Capacity

Fig. 20 — Return Air Pressure Drop

Installing Optional HH57AC081 Single Outside

 

Air Enthalpy Sensor

When using the HH57AC081 (Honeywell C7400S) enthalpy 

sensor (see Fig. 21) for outside air changeover, the existing 

HH79AH001/HH79ZZ007 dry bulb sensor must be removed. The 

enthalpy sensor will be mounted in the same location as the dry 

bulb sensor (see Fig. 1). When the enthalpy sensor’s OA tempera-

ture, enthalpy and dew point are below the respective setpoints, 

the outside air can be used for free-cooling. When any of these is 

above the setpoint, free-cooling will not be available. Figure 22 

shows the enthalpy boundaries in the W7220 controller. There are 

(5) enthalpy boundaries (setpoints ES1 thru ES5), which are 

defined by dry bulb temperature, enthalpy, and dew point. ES3 is 

the default setting. (See Fig. 22.) Single Enthalpy and Dual En-

thalpy High Limit Curves Table on page 9 shows the high limit 

curves for each setting. 
NOTE: To use the HH57AC081 sensor for outside air sensor, the 

dip switches on the sensor must be set to OFF-OFF-OFF. Refer to 

HH57AC081 Sensor DIP Switch Table.
The 2 gray wires with a plug from the EconoMi$er X harness in 

the return chamber plug directly into the HH57AC081 enthalpy 

sensor. See Fig. 23 for wiring and connection.

Table 5 — HH57AC081 Sensor DIP Switch

LEGEND

Fig. 21 — HH57AC081 Dimensional, Connection and 

Switching information

B

A

HOOD

ALUMINUM
FILTER

FI LT ER

CLIP

Relief Air

Outside Air

Cleanable
Aluminum Filter

0

1000

2000

3000

4000

5000

6000

7000

8000

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

Re

lie

f F

lo

w

 (cfm)c

fm

)

RETURN DUCT STATIC PRESSURE (in.wg)

0

1000

2000

3000

4000

5000

6000

7000

0

0.05

0.1

0.15

0.2

0.25

0.3

0.35

0.4

RE

TU

RN

 A

IR

 F

LO

W

 (cfm)c

fm

)

RETURN AIR PRESSURE DROP (in.wg)

USE

DIP SWITCH POSITIONS FOR SWITCHES 1,2, & 3

1

2

3

DA

OFF

ON

OFF

RA

ON

OFF

OFF

OA

OFF

OFF

OFF

DA

— Discharge Air or Supply Sensor

OA

— Outside Air

RA

— Return Air

Default setting is OFF-OFF-OFF.

Summary of Contents for CRECOMZR085A00





















Reviews: