background image

2

GENERAL

The EconoMi$er2  accessories with 4  to 20 mA actuator signal

control,  do  not  have  a  built-in  controller.  The  EconoMi$er2

actuator  is  operated  by  a  4  to  20  mA  signal  from  an  existing

field-supplied  controller  (such  as  PremierLink

  control).

A  12-pin  plug  is  provided  for  connection  to  the  control.  (See

Fig. 1.)

The  EconoMi$er2 system  utilizes  gear-drive technology  with a

direct-mount, spring-return actuator that will close upon loss of

power. Differential dry bulb, enthalpy,  and  differential enthalpy

sensors  are  available  for  field  installation.  Field-installed  CO

2

sensors are available. (See Table 1.)

Standard  barometric  relief  dampers  provide  natural  building

pressurization  control.  An  optional  power  exhaust  system  is

available  for  applications  requiring  even  greater  exhaust

capabilities.  Power  exhaust  is  controlled  by  the  field-supplied

controller.

NOTES:

1. CO

2

 Sensors (Optional)

 a. 33ZCSENCO2  -  Room  sensor  (adjustable).  Aspirator  box  is

required for duct mounting of the sensor.

 b. 33ZCASPCO2 - Aspirator box used for duct-mounted CO

2

 room

sensor.

 c. 33ZCT55CO2 -  Space  temperature  and  CO

room  with  over

-

ride.

 d. 33ZCT56CO2 - Space temperature and CO

2

 room sensor with

override and setpoint.

2. All units include the following standard Sensors:

 a. Outdoor - Air Sensor - HH79NZ039

Fig. 1 — EconoMi$er2 Component Locations

IMPORTANT:  Read  these  instructions  completely  before

attempting to install the accessory EconoMi$er2 system.

IMPORTANT:  These  economizers  meet  all  the  economizer

requirements  as  laid  out  in  California’s  Title  24  mandatory

section 120.2 (fault detection and diagnostics).

Table 1 — Sensor Usage

APPLICATION

OUTDOOR AIR TEMPERATURE 

SENSOR

RETURN AIR TEMPERATURE 

SENSOR

OUTDOOR AIR 

ENTHALPY SENSOR

RETURN AIR 

ENTHALPY SENSOR

DRY BULB 

TEMPERATURE

Included 

HH79NZ039

33ZCSENSAT (Required for 

ComfortLink to Title 24)

DIFFERENTIAL 

DRY BULB 

TEMPERATURE

Included

HH79NZ039

Required — 33ZCSENSAT

SINGLE 

ENTHALPY

Included 

HH79NZ039

33ZCSENSAT (Required for 

ComfortLink to Title 24)

Required — HH57AC077

DIFFERENTIAL 

ENTHALPY

Included 

HH79NZ039

33ZCSENSAT (Required for 

ComforLink to Title 24)

Required — HH57AC077

Outside Air
Damper

Economizer
Actuator

Wiring
Harness

Outside Air
Temp (OAT)
sensor

Return Air Damper

Summary of Contents for CRECOMZR054B00

















Reviews: