Carrier 58MVP040 Installation, Start-Up, And Operating Instructions Manual Download | Manualshive

Page: 6 / 48

background image

e. Cement 2 factory-supplied 1/2-in. street CPVC elbows to

rigid drain tube connection on condensate trap. (See Fig. 5.)
These elbows must be cemented together and cemented to
condensate trap drain connection.

NOTE:

Failure to use CPVC elbows may allow drain to kink,

preventing draining.

f. Connect larger diameter drain tube and clamp (factory-

supplied in loose parts bag) to condensate trap and clamp
securely.

g. Route tube to coupling and cut to appropriate length.

h. Attach tube to coupling and clamp securely.

CONDENSATE TRAP LOCATION (ALTERNATE UPFLOW
ORIENTATION)

An alternate location for the condensate trap is the left-hand side
of casing. (See Fig. 2 and 6.)

NOTE:

If the alternate left-hand side of casing location is used,

the factory-connected drain and relief port tubes must be discon-
nected and modified for attachment. See Condensate Trap Tubing
(Alternate Upflow Orientation) section for tubing attachment.

To relocate condensate trap to the left-hand side, perform the
following:

1. Remove 3 tubes connected to condensate trap.

2. Remove trap from blower shelf by gently pushing tabs inward

and rotating trap.

3. Install casing hole filler cap (factory-supplied in loose parts

bag) into blower shelf hole where trap was removed.

4. Install casing hole filler cap into blower shelf hole where trap

was removed.

5. Fill unused condenstate trap casing holes with placstic filler

caps (factory-supplied in loose parts bag).

CONDENSATE TRAP TUBING (ALTERNATE UPFLOW ORI-
ENTATION)

NOTE:

See Fig. 6 or tube routing label on main furnace door to

confirm location of these tubes.

1. Collector Box Drain Tube

Connect collector box drain tube (blue label) to condensate
trap.

NOTE:

On 17-1/2-in. wide furnaces ONLY, cut tube between

corrugated sections to prevent kinks.

2. Inducer Housing Drain Tube

a. Remove and discard LOWER (molded) inducer housing

drain tube which was previously connected to condensate
trap.

Fig. 5—Factory-Shipped Upflow Tube Configuration

(Shown With Blower Access Panel Removed)

A94213

COLLECTOR BOX

TUBE (PINK)

COLLECTOR BOX

TUBE (GREEN)

INDUCER HOUSING

(MOLDED) DRAIN

TUBE (BEHIND

COLLECTOR BOX

DRAIN TUBE)

COLLECTOR BOX

DRAIN TUBE (BLUE)

FIELD-INSTALLED

FACTORY-SUPPLIED

DRAIN TUBE

COUPLING (LEFT

DRAIN OPTION)

FIELD-INSTALLED

FACTORY-SUPPLIED

DRAIN TUBE

FIELD-INSTALLED

FACTORY-SUPPLIED

DRAIN TUBE

COUPLING (RIGHT

DRAIN OPTION)

CAP

COLLECTOR BOX

DRAIN TUBE (BLUE

& WHITE STRIPED)

PLUG

FIELD-INSTALLED

FACTORY-SUPPLIED

1

⁄

2

-IN. CPVC STREET

ELBOWS (2) FOR

LEFT DRAIN OPTION

CONDENSATE
TRAP

Fig. 6—Alternate Upflow Tube Configuration and

Trap Location

A94214

COLLECTOR BOX

TUBE (PINK)

CONDENSATE

TRAP

COLLECTOR BOX

TUBE (GREEN)

COLLECTOR BOX

DRAIN TUBE (GREEN)

INDUCER

HOUSING

DRAIN TUBE

(VIOLET)

CAP

COLLECTOR BOX

DRAIN TUBE (BLUE

& WHITE STRIPED)

PLUG

6

«
...
4
5
6
7
8
...
»

Summary of Contents for 58MVP040

















































Reviews:

No comments

Related manuals for 58MVP040

Brand: Nagas Pages: 49

Brand: USSC Pages: 28

Brand: Hamilton Pages: 64

Brand: Nordyne Pages: 28

Brand: RANSOM & RANDOLPH Pages: 17

Brand: HVAC Partners Pages: 48

Brand: Barnstead Pages: 44

Brand: Coleman Pages: 6

Brand: ICP Pages: 26

Brand: Haier Pages: 56

Brand: United States Stove Pages: 24

Brand: ICP Pages: 42

Brand: Thermo Pride Pages: 21

Brand: Thermo Pride Pages: 66

Brand: Alpine Pages: 9

Brand: Alpine Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands