manualshive.com logo in svg

Carrier 58MVP040, Installation, Start-Up, And Operating Instructions Manual

The Carrier 58MVP040 is a high-quality heating and cooling system designed to keep your home comfortable year-round. Easily set up and maintain this efficient unit with the help of the comprehensive "Installation, Start-Up, and Operating Instructions Manual". Download this manual for free from our website, making installation a breeze.

Share
Download
background image

58MVP

4-Way Multipoise Direct-Vent

Variable-Capacity Condensing Gas Furnace

Installation, Start-Up, and Operating Instructions

For Sizes 040—120, Series 140 and 150

This symbol

→

indicates a change since the last issue.

Index

Page

DIMENSIONAL DRAWING........................................................3
SAFETY CONSIDERATIONS .....................................................2

Clearances to Combustibles......................................................4

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS........2
INTRODUCTION.......................................................................2-4
APPLICATIONS ......................................................................5-11

General ......................................................................................5
Upflow Applications..............................................................5-7
Downflow Applications.........................................................7-8
Horizontal Left (Supply-Air Discharge) Applications .......8-10
Horizontal Right (Supply-Air Discharge) Applications ...10-11

LOCATION ............................................................................11-13

General...............................................................................11-12
Low-Fire Only Installation .....................................................13
Furnace Location Relative to Cooling Equipment ................13
Hazardous Locations...............................................................13

INSTALLATION....................................................................13-14

Leveling Legs (If Desired) .....................................................13
Installation In Upflow or Downflow Applications ..........14-15
Installation In Horizontal Applications ..................................14

AIR DUCTS............................................................................14-18

General Requirements.............................................................14
Ductwork Acoustical Treatment.............................................14
Supply-Air Connections..........................................................14
Return-Air Connections ..........................................................14
Filter Arrangement ............................................................16-17
Bottom Closure Panel.............................................................17
Gas Piping..........................................................................17-18

ELECTRICAL CONNECTIONS...........................................18-22

115-v Wiring......................................................................18-19
24-v Wiring.............................................................................19
Accessories ........................................................................21-22

DIRECT VENTING ...............................................................22-31

Removal of Existing Furnaces from

Common Vent Systems.....................................................23

Combustion-Air and Vent Piping...........................................23
Concentric Vent and Combustion-Air Termination

Kit Installation..............................................................28-31

Multiventing and Vent Terminations .....................................31

CONDENSATE DRAIN ........................................................31-33

General...............................................................................31-32

Application ..............................................................................31
Condensate Drain Protection ..................................................31

SEQUENCE OF OPERATION..............................................33-36

Self-Test Mode........................................................................33
Heating Mode..........................................................................33
Heating Mode—Two Stage ....................................................34
Emergency Heat Mode ...........................................................34
Cooling Mode .........................................................................34
Heat Pump Mode...............................................................34-35
Continuous Fan Mode .......................................................35-36
Component Test ......................................................................36
Bypass Humidifier Mode........................................................36
Dehumidification Mode ..........................................................36
Zone Mode ..............................................................................36

START-UP PROCEDURES ..................................................36-45

General ....................................................................................36
Select Setup Switch Positions ................................................37
Prime Condensate Trap With Water ......................................37
Purge Gas Lines......................................................................38
Adjustments .......................................................................38-45
Set Gas Input Rate ............................................................38-44
Set Temperature Rise..............................................................44

A93040

NOTE:

Read the entire instruction

manual before starting the installation.

ama

CERTIFIED

As an ENERGY STAR®
Partner, Carrier Corpora-
tion has determined that
this product meets the EN-
ERGY STAR® guidelines
for energy efficiency.

REGISTERED QUALITY SYSTEM

Fig. 1—Multipoise Orientations

A93041

UPFLOW

DOWNFLOW

HORIZONTAL

LEFT

AIRFLOW

AIRFLOW

AIRFLOW

AIRFLOW

HORIZONTAL

RIGHT

Visit www.carrier.com

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Book 1

4

Tab

6a 8a

PC 101

Catalog No. 535-80021

Printed in U.S.A.

Form 58MVP-11SI

Pg 1

2-01

Replaces: 58MVP-10SI

Summary of Contents for 58MVP040

















































Reviews:

No comments

Related manuals for 58MVP040

Trane TDD-ACV User'S Information Manual preview
TDD-ACV
Brand: Trane Pages: 12
Paragon W13 Operating Instructions Manual preview
W13
Brand: Paragon Pages: 19
DAKA 521FB Manual preview
521FB
Brand: DAKA Pages: 32
York GY8S-DH Technical Manual preview
GY8S-DH
Brand: York Pages: 8
Kenmore Condensing gas furnaces User'S Information Manual preview
Condensing gas furnaces
Brand: Kenmore Pages: 36
ICP N9MP1100F14A2 Installation Instructions preview
N9MP1100F14A2
Brand: ICP Pages: 2
United States Stove Clayton 1602M Installation & Operator'S Manual preview
Clayton 1602M
Brand: United States Stove Pages: 20
Oxbox G7 Series Installation Instructions Manual preview
G7 Series
Brand: Oxbox Pages: 8
York M9E080B12 Installation Manual preview
M9E080B12
Brand: York Pages: 36
Atwood HYDRO FLAME 2540 User Manual preview
HYDRO FLAME 2540
Brand: Atwood Pages: 6
Sears 867.763792 Owner'S Manual preview
867.763792
Brand: Sears Pages: 30
Heatilator Gas Fireplace IDV4833IH Owner'S Manual preview
Gas Fireplace IDV4833IH
Brand: Heatilator Pages: 68
Goodman GME80603B Series Specifications preview
GME80603B Series
Brand: Goodman Pages: 8
Goodman GM9S96 Manual preview
GM9S96
Brand: Goodman Pages: 8
Goodman GMS90453BXA Repair Parts preview
GMS90453BXA
Brand: Goodman Pages: 11
Goodman GM9S80-U Series Specification Sheet preview
GM9S80-U Series
Brand: Goodman Pages: 10
Goodman GHS80453AXCA Repair Parts preview
GHS80453AXCA
Brand: Goodman Pages: 10
Goodman GDH80453AXCA Repair Parts preview
GDH80453AXCA
Brand: Goodman Pages: 10

Brands by name

Popular brands

Load more brands