manualshive.com logo in svg

Carrier 58MSA Series, Installation, Start-Up, And Operating Instructions Manual

Share
Download
Carrier 58MSA Series Installation, Start-Up, And Operating Instructions Manual Download Page 20

If a flexible connector is required or allowed by authority
having jurisdiction, black iron pipe shall be installed at
furnace gas control valve and extend a minimum of 2 in.
outside furnace casing. Failure to follow this caution will
result in potential shaffing of flexible gas connection.

If local codes allow the use of a flexible gas appliance connector,
always use a new listed connector. Do not use a connector which
has previously served another gas appliance.

FIRE OR EXPLOSION HAZARD
Failure to follow the safety warnings exactly could result in
serious injury, death or property damage.
Never test for gas leaks with an open flame. Use a commer-
cially available soap solution made specifically for the
detection of leaks to check all connections. A fire or explo-
sion may result causing property damage, personal injury or
loss of life.

An accessible manual shutoff valve MUST be installed external to
the furnace casing and within 6 ft of furnace. A 1/8-in. NPT
plugged tapping, accessible for test gage connection, MUST be
installed immediately upstream of gas supply connection to
furnace and downstream of manual shutoff valve.

NOTE:

The gas valve inlet press tap connection is suitable to use

as test gauge connection providing test pressure DOES NOT
exceed maximum 0.5 psig (14-in. wc) stated on gas valve. (See
Fig. 46.)

Piping should be pressure and leak tested in accordance with
NFGC in the United States or NSCNGPIC in Canada, local, and
national plumbing and gas codes before the furnace has been

Fig. 24—Crawlspace Horizontal Application

A96209

NOTES:

ANGLE
IRON OR
EQUIVALENT

(B)

(A) ROD LOCATION

USING DIMPLE
LOCATORS
(SEE DIMENSIONAL
DWG FOR
LOCATIONS)

13

/

16

-IN. MAX

ALTERNATE SUPPORT
LOCATION FROM BACK

ALTERNATE SUPPORT
LOCATION 4-IN. MIN
8-IN. MAX

A 3-IN. MINIMUM

CLEARANCE TO

COMBUSTION-AIR INTAKE

IS REQUIRED.

3

⁄

8

-IN. ROD

(A)

(B)

(A)

(B)

(B)

(A)

1. A 1 In. clearance minimum between top of 

furnace and combustible material.

2. The entire length of furnace must be 

supported when furnace is used in 
horizontal position to ensure proper 
drainage.

3. Bottom side combustion-air entry cannot 

be used when furnace is installed with 
hangers as shown.

(A) PREFERRED ROD LOCATION

(B) ALTERNATE ROD LOCATION

DRAIN

5 

3

⁄

4

″

3

/

8

-IN. HEX NUT

& WASHER (4)

REQD PER ROD

VENT

COMBUSTION-AIR

INTAKE

Fig. 25—Filter Installed for Side Inlet

A00217

20

→

Summary of Contents for 58MSA Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands