Carrier 58MEC Installation, Start-Up, And Operating Instructions Manual Download Page 19

Page: 19 / 62

Table 1 –

Minimum Free Area Required for Each Combustion Air Opening or Duct to Outdoors

FURNACE

INPUT

(BTUH)

TWO HORIZONTAL DUCTS

(1 SQ. IN./2,000 BTUH)

(1,100 SQ.

MM/KW)

SINGLE DUCT OR OPENING

(1 SQ. IN./3,000 BTUH)

(734 SQ. MM/KW)

TWO OPENINGS OR

VERTICAL DUCTS

(1 SQ. IN./4,000 BTUH)

(550 SQ. MM/KW)

Free Area of

Opening and

Duct ---

Sq. In (Sq. mm)

Round Duct

In. (mm) Dia

Free Area of

Opening and

Duct ---

Sq. In (Sq. mm)

Round Duct ---

In. (mm) Dia

Free Area of

Opening and

Duct ---

Sq. In (mm)

Round Duct ---

In. (mm) Dia

40,000

20 (12903)

6 (152)

13.4 (8645)

5 (127)

10 (6451)

4 (102)

60,000

30 (19354)

7 (178)

20 (12903)

6 (152)

15 (9677)

5 (127)

80,000

40 (25806)

8 (203)

26.7 (17225)

6 (152)

20 (12903)

6 (152)

100,000

50 (32258)

8 (203)

33.4 (21548)

7 (178)

25 (16129)

6 (152)

120,000

60 (38709)

9 (229)

40 (25806)

8 (203)

30 (19354)

7 (178)

EXAMPLES: Determining Free Area

FURNACE

WATER HEATER

TOTAL INPUT

100,000

40,000

= (140,000 divided by 4,000)

= 35.0 Sq. In. for each two Vertical Ducts or Openings

60,000

40,000

= (100,000 divided by 3,000)

= 33.4 Sq. In. for a Single Duct or Opening

80,000

30,000

= (110,000 divided by 2,000)

= 55.0 Sq. In. for each of two Horizontal Ducts

Table 2 –

Minimum Space Volumes for 100% Combustion, Ventilation and Dilution Air from Outdoors

OTHER THAN FAN-ASSISTED TOTAL

(1,000’S BTUH GAS INPUT RATE)

FAN-ASSISTED TOTAL

(1,000’S BTUH GAS INPUT RATE)

ACH

110

132

154

Space Volume Ft

)

0.60

1,050

(29.7)

1,400

(39.6)

1,750

(49.5)

1,100

(31.1)

1,650

(46.7)

2,200

(62.2)

2,750

(77.8)

3,300

(93.4)

3,850

(109.0)

0.50

1,260

(35.6)

1,680

(47.5)

2,100

(59.4)

1,320

(37.3)

1,980

(56.0)

2,640

(74.7)

3,300

(93.4)

3,960

(112.1)

4,620

(130.8)

0.40

1,575

(44.5)

2,100

(59.4)

2,625

(74.3)

1,650

(46.7)

2,475

(70.0)

3,300

(93.4)

4,125

(116.8)

4,950

(140.1)

5,775

(163.5)

0.30

2,100

(59.4)

2,800

(79.2)

3,500

(99.1)

2,200

(62.2)

3,300

(93.4)

4,400

(124.5)

5,500

(155.7)

6,600

(186.8)

7,700

(218.0)

0.20

3,150

(89.1)

4,200

(118.9)

5,250

(148.6)

3,300

(93.4)

4,950

(140.1)

6,600

(186.8)

8,250

(233.6)

9,900

(280.3)

11,550

(327.0)

0.10

6,300

(178.3)

8,400

(237.8)

10,500

(297.3)

6,600

(186.8)

9,900

(280.3)

13,200

(373.7)

16,500

(467.2)

19,800

(560.6)

23,100

(654.1)

0.00

b. Not less than the sum of the areas of all vent

connectors in the space.

The opening shall commence within 12 in. (305 mm)

of the ceiling. Appliances in the space shall have

clearances of at least 1 in. (25 mm) from the sides and

back and 6 in. (153 mm) from the front. The opening

shall directly communicate with the outdoors or shall

communicate through a vertical or horizontal duct to

the outdoors or spaces (crawl or attic) that freely

communicate with the outdoors.

Indoor Combustion Air

NFPA & AGA

Standard

and

Known-Air-Infiltration Rate

Methods

Indoor combustion air

is permitted for combustion, ventilation,

and dilution, if the

Standard

Known-Air-Infiltration Rate

Method is used.

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in death and/or

personal injury.
Many homes require air to be supplied from outdoors for

furnace combustion, ventilation, and dilution of flue gases.

The furnace combustion air supply must be provided in

accordance with this instruction manual.

WARNING

The

Standard

Method:

1. The space has no less volume than 50

ft. (1.4

M) (per

1,000 Btuh of the maximum input ratings for all gas

appliances installed in the space and

2. The air infiltration rate is not known to be less than 0.40

air changes per hour (ACH).

The

Known Air Infiltration Rate

Method shall be used, if the

infiltration rate is known to be:

1. Less than 0.40 ACH and
2. Equal to or greater than 0.10 ACH

Infiltration rates greater than 0.60 ACH shall not be used. The

minimum required volume of the space varies with the number of

ACH and shall be determined per Table 2 or Equations 1 and 2.

Determine the minimum required volume for each appliance in

the space and add the volumes together to get the total minimum

required volume for the space.
Table 2 -- Minimum Space Volumes were determined by using the

following equations from the

National Fuel Gas Code ANSI

Z223.1--2009/NFPA 54--2009,9.3.2.2:

58MEC

Summary of Contents for 58MEC































































Search results

Summary of Contents for 58MEC

Reviews:

Related manuals for 58MEC

Brands by name

Popular brands

Carrier 58MEC, Installation, Start-Up, And Operating Instructions Manual

Search results

Summary of Contents for 58MEC

Reviews:

Related manuals for 58MEC

Brands by name

Popular brands