![background image](http://html.mh-extra.com/html/carrier/53g100hf/53g100hf_owners-manual_2561764007.webp)
BEFORE OPERATION
BEFORE OPERATION
Indicates the selected operating mode.
Lights up when the signal from the remote
control is transmitted.
A receiving beep is heard from the unit.
Lights up when the batteries must be
replaced with new ones. When this mark
appears, replace the batteries within a
week.
Lights up when the unit is operating.
Indicates the selected temperature.
Indicates flap modes
Indicates the reserved status of SLEEP timer or
EVERYDAY timer.
Indicates the reservation time of ON timer and
OFF timer or the current time.
Indicates the selected fan speed.
Remove the cover of the
battery compartment at the
back of the remote control by
sliding it out in the direction of
the arrow.
1
2
3
4
5
6
7
8
9
REMOTE CONTROL PREPARATION
Remote Control Display
Remove the used batteries and
insert new batteries. The remote
control uses two alkaline batteries.
(1.5V, LR03x2)
Press the RST button with a sharp
object to reset the remote control .
1
2
3
• Do not fit use the used batteries or batteries of a different type. Such use may cause the unit to malfunction.
• Changing batteries should be done after turning off the unit.
• The average battery life during normal use is approximately one year.
• When the air conditioner does not operate normally after replacing the batteries, remove the batteries, refit
them and repress the RST button after 5 seconds.
• TA/RST button may locate back side near battery compartment for some models.
NOTE
Replacing Batteries
Setting Current Time
NOTE
• This function must only be performed by qualified service personnel.
When two units are used in the same room, you can match the address of the remote control to that of the unit.
Remove the lid of the battery case. Assign the address switch of one remote control as B.
Press the RST button with a sharp object.
Turn off the unit and pull out the power plug. Remove the front panel, Terminal block cover, and Frame grille.
Pull out the PCB. Assign the address switch of one indoor unit as B.
1
2
3
Matching Address between Indoor Unit and Remote Control
Press the TA button with a sharp
object and the current time
indication symbol flashes. In the
beginning, 6:00A.M. will flash.
Set the current time with the hour
and the minute buttons while the
current time indication flashes.
Press the TA button again.
The flashing will stop and the
current time will be set.
4
5
6
COOL
DRY
FAN
A
HEAT
AUTOMATIC CHANGEOVER
ON/OFF
SLEEP
MODE
FAN
FLAP
CLOCK
EVERYDAY
SET
RST
TA
TIMER
ON
OFF
CANCEL
TEMP.
HOUR MINUTE
ON/OFF
SLEEP
MODE
FAN
FLAP
CLOCK EVERYDAY
RST
TA
TIMER
ON
OFF
CANCEL
TEMP.
HOUR MINUTE
RESERV.
ON/OFF
SLEEP
MODE
FAN
FLAP
CLOCK EVERYDAY
SET
RST
TA
TIMER
ON
OFF
CANCEL
TEMP.
HOUR MINUTE
RST TA
LR03(AM4)1.5V
LR03(AM4)1.5V
RST TA
LR03(AM4)1.5V
LR03(AM4)1.5V
ON/OFF
SLEEP
MODE
FAN
FLAP
CLOCK EVERYDAY
SET
RST
TA
TIMER
ON
OFF
CANCEL
TEMP.
HOUR MINUTE
OWNER
,
S MANUAL - 10
OWNER
,
S MANUAL -11
A
SWING
A
햲
햳
햴
햷
햸
햺
햵
햶
햹
Automatic position
User selected position
Swing up and down
AUTO
SWING
AUTO
LOW
MED
HIGH
A
42QG8V5404B(O/M-P)
2004.7.7, 2:40 PM
10-11