manualshive.com logo in svg

Carrier 42HQM 009, Installation Manual, Page: 2 / 14

Share
Download
Carrier 42HQM 009 Installation Manual Download Page 2

ENGLISH

42HQM
Split system “Hi-Wall INVERTER” indoor unit

ENGLISH

GB - 1

For operation and maintenance instructions of this unit, as well as installation
instructions of the outdoor unit, refer to the relevant manuals.

Contents

Page

Dimensions and weight...............................................................................

2

Nominal data ...............................................................................................

2

Operating limits ...........................................................................................

2

Minimum clearances ...................................................................................

3

Material supplied ........................................................................................

3

General information ....................................................................................

4

Warnings: avoid ..........................................................................................

5

Installation ..................................................................................................

6/9

Refrigerant connections .............................................................................

10

Electrical connection ..................................................................................

11

Address switch ............................................................................................

12

Guide for the owner ....................................................................................

12

Accessories ................................................................................................

12

Model

Power supply

42HQM009

230V  ~  50Hz

42HQM012

Summary of Contents for 42HQM 009















Reviews:

No comments