background image

5

in accordance with the national usage regulations:
• 

These relief valves and fuses are not safety accessories 
but damage limitation accessories in case of a fire,

• 

The high pressure switches are the safety accessories.

The relief valve must only be removed if the fire risk is 
fully controlled and after checking that this is allowed by 
local regulations and authorities. This is the responsibility 
of the operator.

When the unit is subjected to fire, safety devices prevent 
rupture due to over-pressure by releasing refrigerant. The 
fluid may then be decomposed into toxic residues when 
subjected to the flame:

• 

Stay away from the unit

• 

Set up warnings and recommendations for personnel 
in charge to stop the fire.

• 

Fire extinguishers appropriate to the system and the 
refrigerant type must be easily accessible.

The external relief valves must in principle be connected 
to discharge pipes for units installed in a room. Refer to 
the installation regulations, for example those of European 

standards EN 378 and EN 13136.

They include a sizing method and examples for configura-
tion and calculation. Under certain conditions these stan-
dards permit connection of several valves to the same 
discharge pipe. Note: Like all other standards these EN 
standards are available from national standards organi-

sations. 

These pipes must be installed in a way that ensures that 
people and property are not exposed to refrigerant leaks. 
These fluids may be diffused in the air, but far away from 
any building air intake, or they must be discharged in a 
quantity that is appropriate for a suitably absorbing 

environment.

It is recommended to install an indicating device to show 

if part of the refrigerant has leaked from the valve. The 
presence of oil at the outlet orifice is a useful indicator 
that refrigerant has leaked. Keep this orifice clean to 
ensure that any leaks are obvious.

The calibration of a valve that has leaked is generally 
lower than its original calibration. The new calibration 
may affect the operating range. To avoid a nuisance 
tripping or leaks, replace or re-calibrate the valve.

Periodic check of the relief valves: See paragraph 1.3 
“Maintenance safety considerations”.

Provide a drain in the discharge circuit, close to each 
relief valve, to avoid an accumulation of condensate or 

rain water. 

Ensure good ventilation, as accumulation of refrigerant 
in an enclosed space can displace oxygen and cause 
asphyxiation or explosions.

Inhalation of high concentrations of vapour is harmful 
and may cause heart irregularities, unconsciousness, or 

death. Vapour is heavier than air and reduces the amount 

of oxygen available for breathing. These products cause 

eye and skin irritation. Decomposition products are 

hazardous.

1.2 - Equipment and components under pressure

The units are intended to be stored and operate in an 
environment where the ambient temperature must not be 
less than the lowest allowable temperature indicated on 
the nameplate. See section “11.2 - Pressure vessels”.

1.3 - Maintenance safety considerations

Carrier recommends the following drafting for a logbook 
(the table below should not be considered as reference 
and does not involve Carrier responsibility):

Intervention

Name of the 

commissioning 

engineer

Applicable 

national 

regulations

Verification 

Organism

Date

Nature

 (1)

(1)   Maintenance, repairs, regular verifications (EN 378), leakage, etc.

Engineers working on the electric or refrigeration compo-

nents must be authorized, trained and fully qualified to do so.

All refrigerant circuit repairs must be carried out by a trained 

person, fully qualified to work on these units. He must have 

been trained and be familiar with the equipment and the 
installation. All welding operations must be carried out by 

qualified specialists.

The insulation must be removed and heat generation must 
be limited by using a wet cloth.

Any manipulation (opening or closing) of a shut-off 
valve must be carried out by a qualified and authorised 
engineer. These procedures must be carried out with the 
unit shut-down.

NOTE: The unit must never be left shut down with the 
liquid line valve closed, as liquid refrigerant can be trapped 
between this valve and the expansion device. (This valve 
is situated on the liquid line before the filter drier box.)

Equip the engineers that work on the unit as follows:

Personal protection 

equipment (PPE) 

(1)

Operations

Handling Maintenance, 

service

Welding or brazing

(2)

Protective gloves,

eye protection,

safety shoe,

protective clothing.

Fuse plug

x

x

x

Ear protection.

x

x

Filtering respirator.

x

(1)  We recommend to follow the instructions in EN 378-3.

(2)  Performed in the presence of A1 refrigerant according to EN 378-1.

Never work on a unit that is still energized. 

Never work on any of the electrical components, until the 
general power supply to the unit has been cut using the 
disconnect switch(es) in the control box(es). 

Summary of Contents for 30XW





































Reviews: