manualshive.com logo in svg

Carrier Access Network Device Adit 3104, User Manual, Page: 33 / 74

Share
Download
Carrier Access Network Device Adit 3104 User Manual Download Page 33

Adit 3104 - Release 1.6

3-3

 

Electrical Installation & Cabling

Interface Connectors

Interface Connectors

The following are the Adit 3104 interface connectors:

Front of Adit

(1) DS1 WAN port (RJ-48C). Note: E1 will be in a future release.
(1) 10/100Base-T WAN port (RJ-45)
(4) 10/100Base-T switched LAN ports (RJ-45)
Tip and Ring Analog Interface equipped with standard 25-pair Telco Connector 

Back of Adit

RS-232 craft port connector for local management
Power input connector
Ground connector

Grounding the Unit

WARNING!   

T

HE

 A

DIT

 3104 

ARE

 

REQUIRED

 

TO

 

BE

 

PERMANENTLY

 

GROUNDED

 

FOR

 

THE

 

PROTECTION

 

OF

 

USERS

 

AND

 

SERVICE

 

PERSONNEL

. 

Chassis ground is located on the back of the unit. 
To ground the unit:

1. Connect a minimum 14 AWG ground 

wire with a #8 ring tongue terminal (not 
included) to the chassis ground on the 
back of the unit. Secure with the 8-32 
screw and lock washer provided.

2. Connect the opposite end of the ground 

wire to a suitable earth grounding point 
such as a building grounding electrode, 
metal water pipe, or metal building 
structure that is in compliance with article 250 of NEC.

Chassis 
Ground

Summary of Contents for Network Device Adit 3104











































































Reviews:

No comments