background image

Carpenter Model 59 Wire Prefeed & Dereeler 

Carpenter Model 59 Wire Prefeed & Dereeler

 

• 

Phone

: (315) 682-

9176 • 

Fax

: (315) 682-9160 

Website

: www.carpentermfg.com • 

Email

[email protected]

 

 

Revised 09/27/2021 

 

Page 22

 

Section 6

 

– 

Warranty 

 
Carpenter Mfg. Co., Inc. manufactures its products to be free from defects in materials 
and workmanship.  Should any defect occur within the warranty period, Carpenter Mfg. 
Co. Inc. will, at its option, exchange or repair the defective device. 
 
At the discretion of Carpenter Mfg. Co., Inc., repairs or adjustments to equipment under 
warranty can be performed at our factory or at the customer location.  In most cases a 
1- or 2-day turnaround time will be necessary to repair equipment at our facility.  When 
equipment is returned to our factory for repair or replacement, the customer is 
responsible for all freight charges. 
 
This is a limited warranty and is in lieu of all other representations and expressed and 
implied warranties (including the implied warranties of merchantability and fitness for 
use).  Under no circumstances shall Carpenter Mfg. Co., Inc. be liable for any incidental 
or consequential property damages or losses subsequent to misuse or improper 
maintenance of this equipment. 
 

The following are not covered by the latter warranty

  Consumable parts (blades, belts, guides, springs, inserts, stripping wheels, etc.) 

  Cosmetic problems (nicks, scratches, etc.) 

  Damages caused by any repairs or modifications by unauthorized personnel 

  Damages caused by abuse 

  Damages caused by shipping 

  Damages caused by environmental and/or atmospheric conditions 

  Damages caused by the use of contaminated compressed air 

 

Summary of Contents for 59























Reviews: