background image

© 2012, Carmanah Technologies Corporation. 63966_EG_Series_UserManual_RevB

EG-SERIES USER MANUAL

SEttING bRIGhtNESS ANd PRoGRAMMING

7

Setting brightness and 

Programming

As part of the installation process, the EG-series is config-

ured with a fixture current, which sets the base fixture 

brightness, and an operating profile, which controls fixture 

on/off times and, for some profiles, fixture dimming.

The current setting for every EG-series system is carefully 

chosen to work together with the operating profile without 

consuming more than the available solar energy in the 

installation location.

The EG-series is configured in two steps: 1) installing the 

fixture current-setting resistor, and 2) programming the 

EMS using the EG-series Programmer.

Installing the current-setting resistor

The amount of current going to the LED fixture(s) is deter-

mined by the current setting resistor, which is installed in a 

sealed holder in the EG-series EMS wiring harness.  When 

no resistor is installed, the fixture current reverts to the 

lowest possible setting.

The current-setting resistor should be inserted into the 

holder during the installation of the EG-series system (see 

EG-series Installation Guide for details).  If this step was 

forgotten during installation, the current-setting resistor can 

be installed by:

EG320/340/500: pulling the resistor holder out through the 

access hole under the EMS, removing the holder cap, and 

inserting the resistor. 

EG40/80/145: tilting the solar panel forward, removing the 

holding cap, and inserting the resistor.

The current-setting resistor can be inserted into the holder 

in any orientation.  Make sure it is seated firmly in the 

electrical contacts.

Programming using the EG-Series 

Programmer

The EG-series Programmer is used to upload 

(program) the operating profile into the EG-series 

EMS.  This should be done during installation of the 

system (see EG-series Installation Guide for details).

Follow these steps to program the EMS:

• Make sure the knobs and switches are positioned

as indicated by the label on the EG-series

programmer.

• Point the programmer at the infrared transmitter/

receiver on the EG-series EMS.

• Press 

and hold

 the Send button on the

programmer.

Continue

 to hold down the Send button until the

programmer beeps.

• If the Programmer beeps three times and the green

OK light on the programmer lights, programming

was successful.

• If the Programmer emits one long beep and the red

Error light on the programmer lights, programming

was not successful.

If programming was not successful, try getting closer 

to the EG-series EMS and make sure you accu-

rately aim the programmer at the infrared transmit-

ter/receiver on the EMS while pressing and holding 

the Send button.  Programming can be done from 

the ground, but may not work during the middle of 

the day, when the strong infrared radiation from the 

sun interferes with communications between the 

Programmer and EMS.

Summary of Contents for EG145

















Reviews: