CHANGING SYSTEM CODE
(optional)
The user can change the system code signal if interference occurs with opera-
tion. If you use other wireless products in your home, there is a slight possibility
of interference. Use the following instructions to change the current system code
setting to a new setting.
Important:
If you change the system code on the motion sensor, you must also
change the code on the light control and remote control. If the system code does
not match on all items, the system will not function properly!
1. Turn off the power to the floodlights.
2. Unscrew the plug on the front of the light control case.
3. Pull out one of the two jumper shunts (black rectangular piece) and reposi-
tion in a different position and note the letter designation for the new jumper
configuration.
4. Replace the plug and turn on the power to the light control.
5. Remove the wireless motion sensor bottom cover.
6. Set the two jumper shunts in the same jumper configuration as in the light
control.
7. Re-install the motion sensor bottom cover.
8. Remove remote control's back cover.
9. Set the two jumper shunts in the same jumper configuration as in the light
control and motion sensor.
10. Replace back cover.
TROUBLESHOOTING TIPS:
PROBLEM:
Floodlights do not come on when there is motion in front of motion
sensor or when turned on by the remote control.
SUGGESTION:
Confirm power is on at circuit breaker. Confirm wall switch has
been turned on. Confirm if unit works with remote control. Set the motion sens-
ing transmitter On-time switch to the "6 s" setting (leftmost position). Verify that
the yellow LED, behind the front lens, turns on when there is motion activity in
front of the motion sensor. If the LED does not turn on, check battery polarity or
replace the batteries in the motion sensor transmitter. Reset the On-time switch
to its original position.
Check that the floodlight assembly and receiver are mounted within 100’ of the
motion sensor or remote control. Check that the system code is the same in the
motion sensor and in the light control. Check that metal objects do not block the
motion sensor signal or move the light control.
PROBLEM:
Floodlights go on and off randomly.
SUGGESTION:
Change the system code in the motion sensor, light control, and
remote control.
SPECIFICATIONS
Motion Sensor
Motion detection range: Up to 60’ x 140˚
Batteries: 4 AA alkaline
Light Control
Maximum Load: 300 watts incandescent total, 150 watts per lampholder
Voltage: 120VAC, 60Hz
Motion sensor also works with HS3605, HW2150D, HW2165D, HW2170D, HW2190,
and RC7000D.
LIMITED WARRANTY
The product you have purchased is guaranteed against defects in workman-
ship and materials for the period stated on the package. Warranties implied
by law are subject to the same time period limitation. Some states do not allow
limitations on how long an implied warranty lasts, so this time limitation may
not apply to you.
If the product fails due to a manufacturing defect during normal use, return the
product and dated sales receipt to the store where purchased for replacement
OR send the product and the dated sales receipt to:
Lamson & Sessions
25701 Science Park Drive
Cleveland, OH 44122 USA
Attn: LHP Customer Service
Not Covered
- Batteries, light bulbs, and other expendable items are not covered
by this warranty. Repair service, adjustment and calibration due to misuse,
abuse or negligence are not covered by this warranty. Unauthorized service or
modification of the product or of any furnished components will void this warranty
in its entirety. This warranty does not include reimbursement for inconvenience,
installation, set-up time, loss of use, postage, unauthorized service, or other
products used in conjunction with, but are not supplied by, Lamson & Sessions.
All requests for replacement must include a
dated sales receipt
(copies accepted).
LAMSON & SESSIONS IS NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL,
EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT
LIMITATION ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE
PRODUCT. As some states do not allow the exclusion or limitation of incidental
or consequential damages, the above limitation and exclusion may not apply
to you.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
This device complies with RSS-210 of Industry Canada.
ALSO AVAILABLE FROM CARLON:
• Extend-A-Chime
®
– lets you hear your existing wired doorbell in remote areas
of your home or yard
• Plug-in and Battery Doorbells and Chimes
• On/Off Remote Switches
• Touch and Automatic Lighting Controls
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
If you have questions or need further
assistance, please call Lamson & Sessions at: 1-800-346-2646 Mon. - Fri.,
9 a.m.-4 p.m. EST
0404 IS158
Made in China
25701 Science Park Drive
Cleveland, Ohio 44122
www.lamson-sessions.com
