background image

EN

This Declaration of conformity / incorporation 
is issued under the sole responsibility of the 
manufacturer:

Carlisle Fluid Technologies UK Ltd, 
Ringwood Road, 
Bournemouth, BH11 9LH. UK

Signed for and on behalf of Carlisle Fluid 

Technologies UK Ltd:

D Smith

Director of Sales (EMEA)

Product Description / Object of Declaration:

Pneumatic Elevator 104112, 104153, 104154, 
104155, DE-05, DE-10, DE-12, DE-15.

This Product is designed for use with:

Solvent and Water based materials

Suitable for use in hazardous area:

Zone 1 / Zone 2

Protection Level:

II 2 G X T4

Notified body details and role:

Element Materials Technology (0891)
Lodging of Technical file

EU Declaration of Conformity

This Declaration of conformity / incorporation is issued under the sole responsibility of the 
manufacturer:

Machinery Directive 2006/42/EC
ATEX Directive 2014/34/EU
by complying with the following statutory documents and harmonized standards:
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
EN ISO 4414:2010  Pneumatic Fluid Power - General Rules and safety requirements
EN 1127-1:2011 Explosive atmospheres - Explosion prevention - Basic concepts
EN 13463-1:2009 Non electrical equipment for use in potentially explosive atmospheres - Basic methods and 
requirements
EN 13463-5:2011 Non electrical equipment for use in potentially explosive atmospheres - Protection by 
constructional safety "c"

Providing all conditions of safe use / installation stated within the product manuals have been complied with and 
also installed in accordance with any applicable local codes of practice.

6/12/17

Bournemouth,BH11 9LH,UK

77-3313 R1.1

2/16

www.carlisleft.com

Summary of Contents for Binks DE-12

















Reviews: