background image

Laser 200

WARNING

A radio-controlled model is not a toy and is not intended for persons under 16 years old.  Keep

this kit out of the reach of younger children, as it contains parts that could be dangerous.  A radio-

controlled model is capable of causing serious bodily injury and property damage.  It is the buyer's

responsibility to assemble this aircraft correctly and to properly install the motor, radio, and all other

equipment. Test and fly the finished model only in the presence and with the assistance of another

experienced R/C flyer.  The model must always be operated and flown using great care and common

sense, as well as in accordance with the Safety Code of the Academy of Model Aeronautics (5151

Memorial Drive, Muncie, IN 47302, 1-800-435-9262).  We suggest you join the AMA and become prop-

erly insured prior to flying this model.  Also, consult with the AMA or your local hobby dealer to find an

experienced instructor in your area.  Per the Federal Communications Commission, you are required

to use only those radio frequencies specified "for Model Aircraft."

LIMITED WARRANTY

Carl Goldberg Products, Ltd. has inspected and certified the components of this aircraft.  The company urges the buyer to perform

his own inspection, prior to assembly, and to immediately request a replacement of any parts he believes to be defective for their

intended use.  The company warrants replacement of any such components, provided the buyer requests such replacement with-

in a period of 

3

0 days from the date of purchase and provided the defective part is returned, if so requested by the company. 

No other warranty, expressed or implied, is made by the company with respect to this kit.  The buyer acknowledges and under-

stands that it is his responsibility to carefully assemble the finished flying model airplane and to fly it safely.  The buyer hereby

assumes full responsibility for the risk and all liability for personal or property damage or injury arising out of the buyer's use of the

components of this kit.

CARL GOLDBERG PRODUCTS, LTD.

P.O. Box 818 Oakwood GA 30566  Phone #678-450-0085 Fax # 770-532-2163  www.carlgoldbergproducts.com

Summary of Contents for Laser 200














Reviews: