background image

052540-002r4 

Printed in USA 

February, 2007 

I

NSTALLATION 

M

ANUAL

 

T

RAVEL

'

A

RMS AND 

C

ANOPY

 

RV

 

T

HIS MANUAL PROVIDES INSTRUCTIONS FOR

O

RIGINAL 

E

QUIPMENT 

M

ANUFACTURER 

(OEM),

 

A

FTERMARKET 

I

NSTALLATIONS AND 

ARM UPGRADES FOR CURRENT 

C

AREFREE AND 

A&E

 

A

WNINGS

 

 

 

T

ABLE OF 

C

ONTENTS

 

Product Overview .......................................................................................................................... 1

 

Travel'r Patio Awning Specifications: .............................................................................................1

 

Component Checklist..............................................................................................................................2

 

Installation ..................................................................................................................................... 3

 

Required Pre-Installation Preparation.....................................................................................................3

 

Installing an Awning Rail.........................................................................................................................4

 

Assembling the Awning ..........................................................................................................................5

 

Mounting the Awning ..............................................................................................................................6

 

Switch and Wiring Installation.................................................................................................................8

 

Securing the Fabric.................................................................................................................................9

 

Removing the Temporary Assembly Pins...............................................................................................9

 

Installing the Tractioners.......................................................................................................................10

 

Attaching the Fascia .............................................................................................................................10

 

 

Summary of Contents for Travel'r Arms and Canopy













Reviews: