background image

Carefree of Colorado 

Service Manual 

Box Awning LED

 

L

IGHTING

 

070013-301r2 

S

WITCH AND 

P

OWER 

I

NSTALLATION

 

W

HITE 

LED 

 

NOTE:  

Installers may

 

choose to furnish the control switch.  The installation requires that the power line 

(+12VDC) be attached to a dedicated 2A circuit breaker or a 2A in-line fuse must be installed between the 
switch and power source.  For easy access, locate the fuse close to the switch. 

The following steps describe the switch and fuse installation using the switch and fuse kit available from Carefree. 

1.  Determine the location of the switch. 

2.  At the switch location, cut a 1 1/8" x 1 1/2" hole. 

3. Wire the switch as shown below.  Wire 

terminals at the switch are .187, 18-24 awg 
female disconnects. 

NOTE: 

Allow adequate slack in the 12VDC 
power line so that the in-line fuse 
(installed in step 4) can be accessed 
from behind the switch. 

4.  Install the in-line fuse: 

4.1. Near the switch, cut the red 12VDC power 

line to the switch.  Do not strip the 
insulation. 

4.2. Insert a wire end into one of the wire 

channels until it butts up against the stop. 

4.3. Fold that half of the connector body over 

until the element contacts the wire.  Use 
pliers to crimp the connector closed. 

4.4. Repeat for the second wire end. 

4.5. Slide the fuse into the fuse port.  Ensure 

that is firmly seated. 

5.  Press the in-line fuse, wires and switch into the 

mounting hole.  Secure the switch using two (2) #6 x 1/2" screws. 

6.  Snap the switch bezel over the switch frame. 

LED002d

Individual Strip

Double Strip

LED Strip

 Vehicle Wall

Red

+12VDC

GND

Switch

18awg Wire

(minimum)

Red

Black

2A In-line Fuse

LED Strip

 Vehicle Wall

Red

+12VDC

GND

Switch

18awg Wire

(minimum)

Red

Black

2A In-line Fuse

LED Strip

Red

Black

See Switch Detail

See Switch Detail

ON

OFF

1.13"

1.5"

1.88"

2.9"

#6 x 1/2" Screw (x2)

2A In-line Fuse

(+12VDC Line)

LED002b

Red

+12VDC

GND

Single Pole, Single Throw Switch

18awg Wire

(minimum)

Red (from power harness)

18-24awg
Female Disconnect (x2)

2A In-line Fuse

Red

+12VDC

Lighted Single Throw Switch

18awg Wire

(minimum)

Red (from power harness)

18-24awg
Female Disconnect (x3)

2A In-line Fuse

Summary of Contents for LED Lighting










Reviews: