manualshive.com logo in svg

Carefree ALTITUDE, Service Manual

Share
Download
Carefree ALTITUDE Service Manual Download Page 15

Carefree of Colorado

 Service 

Manual 

A

LTITUDE

 

070026-301 

13 

E

MERGENCY 

O

VERRIDE

 

If power to the vehicle is not available, the awning can be safely retracted by jumping the motor using a 10V-14V 
power source such as a cordless drill battery or car battery. 

 NOTICE

   

Do not use a 110V power source for the emergency override procedure!  Doing so 

will permanently damage the awning!  Do not use the emergency override without following the 
directions below. 

1.  Remove the front cover.  The cover snaps onto the rear cover.  

To remove, press on both sides of the rear cover until the front 
cover releases then lift the front cover off. 

2. Detach the R

ED

 and B

LACK

 wires from the cable to the 

motor. 

3.  Attach jumper wires to the motor wires. 

4.  Connect the other ends of the jumper leads to a 10-14V 

source.  If the awning moves in the wrong direction, 
reverse the leads.  Maintain contact throughout the 
retraction process. 

5.  When the awning is closed, remove the jumper wires and reattach the cable wires to the motor wires.  

Be sure to match the wire colors. 

6.  Snap the front cover onto the rear cover.  Hang the cover on the top and swing down until it clicks. 

 

Front

Cover

Attach Jumpers to
Wires from Motor

Press on both sides
of the rear cover to
release front cover

Alt014

Summary of Contents for ALTITUDE



















Reviews:

No comments

Brands by name

Popular brands

Load more brands