background image

 
BLF 

 

 

I

NSTALLATION

 

2.1  Unpacking & Handling 

 

When unpacking or moving the furnace always lift it by its base. The furnace contains a 
transformer and is heavy: use two or more people to carry it. Some models may alternatively be 
lifted by fitting lifting bolts to captive threads in the top of the case. 

 

Remove any packing material. 

2.2 

Siting & Setting Up 

 

Place the furnace in a well ventilated room, away from other sources of heat, and on a surface 
which is resistant to accidental spillage of hot materials. Do not mount the furnace on an 
inflammable surface. 

 

Ensure that there is free space around the furnace. Do not obstruct any of the vents in the case: 
there are cooling fans in the case which must not be obstructed. 

 

Ensure that the furnace is placed in such a way that it can be quickly switched off or disconnected 
from the electrical supply - see below. 

2.3 

Fitting the Heating Elements  

Wear eye protection when handling the heating elements. See the warning in section 5.6. 

 

The Molybdenum Disilicide elements are EXCEPTIONALLY FRAGILE and are packed 
separately, together with other items as shown in the list. 

 

separately packed items

Most 
models 

 
BLF 17/8 

Elements 6 

Element clamps 

18 

Element clips 

12 

18 

Braids* 

1 set 

1 set 

Separators 6 

* or combined clips and braids may be supplied 

 

 

Transit Clamps – dependent on model: the example shown here is for the 3 litre models; remove 

any transit clamps as shown. 

 

Remove the complete top access panel using 
the hidden screws in holes in the top of the 
panel: loosen the screws two turns and 
remove the panel 

EHF /3 transit clamps

 

  

Fit the heating elements vertically into the 
chamber. Handle the elements with great 
care. The installation of these elements is 
described later in this manual. 

 

Connect the aluminium braids securely as 
indicated in the element installation 
instructions. 

 

 

 

MF23 

Summary of Contents for BLF 17/3


















Reviews: