background image

  

Version 19.07.2017

 

 

TF-MYGIG 

 

P

age

 

3.

 

Activation of the video-in-motion function 

 

The video-in-motion can be activated and deactivated by Dip 1 or alternatively by the 

included loose green cable in connection with a switch (not included in delivery). 

 

Video-in-motion permanent 

With dip1 to ON the video-in-motion function is activated permanently without disturbing 

the navigation performance. 

 

Video-in-motion selective 

With dip1 to OFF the included green cable is used to activate the video-in-motion function. 

 

Connect a switch to the green cable and connect the green cable to +12V ACC. 

 

+12V  

= TV-Free is activated 

 

0V    

= TV-Free is not activated 

 

Note

: The loose white cable is not required and must be isolated. 

 

 

4.

 

Specifications 

 

Operation voltage 

 

 

10.5 – 14.8V 

Stand-by power drain  

 

>1mA 

Operation power drain 

 

~60mA 

Power consumption   

 

~0,72W 

Temperature range   

 

-30°C bis +80°C 

Weight  

 

 

 

44g 

Measurements (box only) B x H x T  70 x 20 x 47 mm 

 

 

5.

 

Technical Support 

 

Caraudio-Systems Vertriebs GmbH 

manufacturer/distribution

 

In den Fuchslöchern 3 

D-67240 Bobenheim-Roxheim 

 

email  [email protected] 

 

 
 

 

Legal disclaimer:

  Mentioned company and trademarks, as well as product names/codes are registered  

trademarks ® of their corresponding legal owners. 

 

 

Summary of Contents for TF-MYGIG






Reviews: