background image

Before First Use

After unpacking your coffee maker clean all the loose parts with warm water and
make yourself familiar with the different functions. After reading these instructions,
clean the internal parts of the machine by making two carafes using only water,
without any ground coffee inside the filter.

Setting the Clock

1.

When you plug the coffee maker into the outlet the display will flash 12:00. All
indicator lights will be off. 

2.

Press the HOUR or MIN button to advance the time. Fig. 2).

3.

Push and hold the HOUR button. The hours will advance. The display will 
show AM and PM. When the correct hour is displayed release the button 
and push and hold the MIN button to set the minutes. 

Attention

: You must change the clock when the time changes (Standard 

Time, Daylight Savings Time).

Automatic Start Function

If you want the coffee maker to start brewing at a preset time automatically, 
set the automatic start function as follows:
1.

Press PROG button; the display and ON/OFF indicator light will start to  
blink green. (Fig. 2). 

2.

Set the delayed starting time by pressing HOUR and MIN button repetitively 
until the desired time is displayed. Once you have reached the desired start 
time press the PROG button again. The delayed start time is now set. 

3.

Press AUTO button so the green indicator light illuminates. You may check 
the automatic start time by pushing the PROG button when the machine is 
not actively set for the automatic start function. Press PROG again to leave 
the programming mode.   

Note:

You may cancel the automatic start function by pressing the AUTO 

button again until the indicator light turns off.  If you want to change the 
automatic start time, follow the steps above to reset. When the time is due 
the green AUTO indicator light will change from green to red to show that 
the machine has started brewing.  

Using Your Coffee Maker

Coffee makers produce very hot water. If you follow the sequence as described
below you will avoid possible accidents which might cause severe injuries and burns.
1.

Remove carafe from machine and fill carafe with desired amount of water.

Note:

Water will be absorbed during brewing process. The brewed coffee will 

be slightly less than markings on carafe.  

2.

Open the water tank lid (Fig. 1, A) and fill the water tank (Fig. 1, E) with water.

Caution:

The water level should not exceed MAX level marked on the water

level indicator on the side of the machine. If you fill too much water into the 
water tank the carafe may overflow with hot coffee. 

3.

Make sure the removable filter  holder (Fig. 1, D) sits firmly in the filter holder
housing. Then place the GoldTone filter (Fig. 1, C) into the filter holder and 
ensure it fits correctly.

Note:

A size #4 paper filter can also be used instead of the GoldTone filter.

Do not use a filter paper inside a GoldTone filter.

5

Summary of Contents for 414.01









Reviews: