13
Please keep this instruction manual for future reference
Instruction manual INCH
I N S TA L L AT I O N
The installation instruction must be strictly followed as failure to comply could result in
overheating and serious damage to your appliance.
To secure the product to the wall you must initially remove the grease filters. This is achieved by
opening the front panel and pushing the two catches (A) upwards which will then release the
grease filters. Once the grease filters have been removed the front panel should also
be removed.
To secure the product to the wall you must initially remove the grease filters. This is achieved by
opening the front panel and pushing the two catches (A) upwards which will then release the grease
filters. Once the grease filters have been removed the front door panel should also removed.
Open the front panel and remove the two screws (B) as illustrated above. Press the tab (C) down
and remove the front panel from its guides
Secure brackets (D) onto the top of the extractor using the fitting screws and washer (E)
provided. Check that adjustment screw (F) is fitted.
Note: Note some units this bracket may already be fitted.
2
To secure the product to the wall you must initially remove the grease filters. This is achieved by
opening the front panel and pushing the two catches (A) upwards which will then release the grease
filters. Once the grease filters have been removed the front door panel should also removed.
Open the front panel and remove the two screws (B) as illustrated above. Press the tab (C) down
and remove the front panel from its guides
Secure brackets (D) onto the top of the extractor using the fitting screws and washer (E)
provided. Check that adjustment screw (F) is fitted.
Note: Note some units this bracket may already be fitted.
2
Open the front panel and remove the two screws
(B) as illustrated above. Press the tab (C) down and
remove the front panel from its guides.
Secure brackets (D) onto the top of
the extractor using the fitting screws
and washer (E) provided. Check that
adjustment screw (F) is fitted.
NOTE:
Some units this bracket may already
be fitted.
Instruction manual INCH
Instruction manual INCH
Please keep this instruction manual for future reference
Please keep this instruction manual for future reference
10
11
EXTRACTION WITHOUT INTRUSION
The extractor is design to give you the option to extract air to the outside (via
exterior wall), or to re-circulate the air through carbon filters to minimize odours
and vapours.
The choice is yours to decide at the point of installation, and both systems are
explained in this instruction manual.
We recommend that you read this manual from cover to cover before attempting to
install or operate the extractor
INSTALLATION
THE INSTALLATION INSTRUCITON MUST BE STRICTLY FOLLOWED AS FAILURE TO
COMPLY COULD RESULT IN OVERHEATING AND SERIOUS DAMAGE TO YOUR
APPLIANCE
To secure the product to the wall you must initially remove the grease filters. This is achieved by
opening the front panel and pushing the two catches (A) upwards which will then release the grease
filters. Once the grease filters have been removed the front door panel should also removed.
Open the front panel and remove the two screws (B) as illustrated above. Press the tab (C) down
and remove the front panel from its guides
Secure brackets (D) onto the top of the extractor using the fitting screws and washer (E)
provided. Check that adjustment screw (F) is fitted.
Note: Note some units this bracket may already be fitted.
2
To secure the product to the wall you must initially remove the grease filters. This is achieved by
opening the front panel and pushing the two catches (A) upwards which will then release the grease
filters. Once the grease filters have been removed the front door panel should also removed.
Open the front panel and remove the two screws (B) as illustrated above. Press the tab (C) down
and remove the front panel from its guides
Secure brackets (D) onto the top of the extractor using the fitting screws and washer (E)
provided. Check that adjustment screw (F) is fitted.
Note: Note some units this bracket may already be fitted.
2
To secure the product to the wall you must initially remove the grease filters. This
is achieved by opening the front panel and pushing the two catches (A) upwards
which will then release the grease filters. Once the grease filters have been removed
the front door panel should also removed.
Open the front panel and remove the
two screws (B) as illustrated above. Press
the tab (C) down and remove the front
panel from its guides
Secure brackets (D) onto the top
of the extractor using the fitting
screws and washer (E) provided.
Check that adjustment screw (F) is
fitted.
Note: Note some units this bracket
may already be fitted.
Ensuring there is a minimum distance if 65cm between the bottom of the extractor
and hob surface., the two mounting brackets (G) to the rear wall.
Once the two mounting brackets are in position hook the extractor mounting
bracket (D) onto the wall mounting bracket
Some adjustment is provide within the brackets. For forward and backward
adjustment use screw (E) and for height alignment adjust screws (F).
Once the adjustment is complete fully tightening all screws.
If after installation there is a gap between the rear wall and the extractor a spacer is
provided. This can be fixed to the rear of the extractor and cut to accommodate the
gap.
