background image

 

AUG 2017 V3 

9.

 

DO NOT USE MASTIC OR SEAL BEHIND THE FLANGE.    THIS WILL PREVENT THE APPLIANCE FROM OPERATING CORRECTLY.

   

Once the appliance is in position, lock the steel cable by threading it through the hole in the flange indicated in images 9 and 10 

below. 

, then align the cable with the joint in the flange

, and 

10.

 

Pull the cable through the joint in the flange until it locates in the hole as indicated in images 11, 12, 13 and 14 below.    Cut off 
the excess cable length with wire cutters.    Should the appliance need to be replaced, then the cable may be cut. 

 

 

 

 

11.

 

Now fit the Fireframe and screw in the two retaining screws at the bottom of the Fireframe 
behind the ash pan cover. As shown in image 15 to the right. 

12.

 

As an alternative method of providing stability, it is possible to screw fix the appliance to the 
wall or back panel through the flanges.    Take care when drilling to ensure that the edges of 
the opening are not “blown”. 

 

 

 

 

 

 

c.

 

CAPITAL TRIM AND FRET OPTION 

1.

 

Remove the feet from the appliance by unscrewing the 4 screws locating in the positions shown in image 16 below.    Retain the 
screws for possible future re-use. 

If the appliance is to be fitted with a trim and fret, then the canopy should not be removed. 

 

 

 

2.

 

FOLLOW STEPS 4 TO 10 ABOVE UNDER THE FIREFRAME SECTION

 

 

3.

 

Now fit the magnetic trim to the flange of the appliance and position the fret symmetrically between the legs of the trim and 
just in front of the fuel bed. 

4.

 

As an alternative method of providing stability, it is possible to screw fix the appliance to the wall or back panel through the 
flanges.    Take care when drilling to ensure that the edges of the opening are not “blown”. 
 

 

 
 
 

All rights reserved.    Information contained in this manual may not be reproduced in whole or in part without prior permission in writing from Capital Fireplaces Ltd. 

IMAGE 9 

IMAGE 10 

IMAGE 11 

IMAGE 12 

IMAGE 13 

IMAGE 14 

IMAGE 15 

IMAGE 16 

Summary of Contents for TF-1561ERA

Page 1: ...TASY ELECTRIC FIRE TF 1561ERA FEATURING THE WHISPERGLOW FLAME EFFECT This product is only suitable for well insulated spaces or occasional use For use if the customer has decided to install the PHANTASY ELECTRIC FIRE in front of a fireplace ...

Page 2: ...r 3 and less than 8 years shall not plug in regulate clean nor maintain the appliance o Children of any age should not be permitted to play with the appliance or its controls o Never route the supply cable near the heater outlet of the appliance or under floor coverings If the supply cord is damaged it must be replaced by a suitably competent and qualified person o The appliance must not be sited ...

Page 3: ...t slack to enable the appliance to be connected 5 Centrally and in line with the top of the fireplace opening drill and plug a hole and fit the eyelet supplied in the rear wall of the chamber Ensure the fittings you use are suitable for the structure into which you are fitting the eyelet Please see sketch 5 to the right 6 Position the appliance in front of the fireplace opening and connect the pow...

Page 4: ... flanges Take care when drilling to ensure that the edges of the opening are not blown c CAPITAL TRIM AND FRET OPTION 1 Remove the feet from the appliance by unscrewing the 4 screws locating in the positions shown in image 16 below Retain the screws for possible future re use If the appliance is to be fitted with a trim and fret then the canopy should not be removed 2 FOLLOW STEPS 4 TO 10 ABOVE UN...

Reviews: