background image

 

 

I/O MANUAL Horizontal/Modular/Vertical/Rooftop AHU 2015pg

28

 

COMMERCIAL AIRE PRODUCTS     501 Terminal Road, Fort Worth TX 76106 

Tel: 817-624-0820

 

 

LIMITED WARRANTY 

Commercial Aire (CAP) warrants this product to be free from defects in factory workmanship and material for a term of ONE YEAR 
under normal use and service. CAP will, at its option, repair or replace any parts that prove to have such defects according to the terms 
outlined below. This warranty covers only the equipment described by the product Model and Serial Number listed below. 
For your benefit and protection, fax this completed sheet to CAP at (817) 624-8581 promptly after installation. This will initiate the 
warranty period. In the absence of recorded warranty coverage, the warranty period will begin upon date of manufacture based upon 
the serial number provided. The warranty period for repair or replacement parts shall not exceed 2 years from date of manufacture. 
This warranty extends only to the original consumer purchaser and is non-transferable. For this warranty to apply the product must be 
installed according to CAP recommendations and specifications, and in accordance with all local, state, and national codes; and the 
product must not be removed from its place of original installation.  
CAP strongly recommends regular periodic preventative maintenance on this equipment. A licensed contractor can ensure your 
maintenance program meets the conditions of the warranty, maximize the efficiency of the equipment, and service your unit wit hin 
the mandated guidelines with regard to unlawful discharge of refrigerants into the atmosphere. 
This warranty applies only to products installed in the United States and Canada. 
For Owner's Information: 
PRODUCT MODEL. NO. _____________________________________ INSTALLATION DATE____________ 
UNIT SERIAL NO. __________________________________INSTALLED BY: _________________________ 
CONTRACTOR PHONE #  ______________________ CONTRACTOR LICENSE #______________________                                                                                                                                         

EXCLUSIONS 

This warranty does not cover any: 

  1.

 Shipping, labor, or material charges (including Refrigerant). 

  2.

 Damages resulting from transportation, installation, or servicing. 

  3.

 Damages resulting from: use of the product in a corrosive atmosphere; accident; abuse; fire; flood; alteration; or acts of  G od. 

Tampering, altering, defacing or removing the product serial number will void this warranty. 

  4.

 Damages resulting from inadequacy or interruption of electrical service or fuel supply, improper voltage conditions,  

      

Blown fuses, or other like damages. 

  5.

 Cleaning or replacement of filters. 

  6

. Damages resulting from failure to properly and regularly clean air and/or water side of condenser and evaporator. 

  7.

 Damages resulting from: (

a

) freezing of condenser water or condensate; (

b

) inadequate or interrupted water supply;   (

c

) Use of 

corrosive water; (

d

) fouling or restriction of the water circuit by foreign material or like causes. 

  8

. Damages resulting from operation with inadequate supply of air or water. 

  9

. Damages resulting from use of components or accessories not manufactured or approved by Commercial Aire.  

10

. Increase in fuel or electric cost. 

This warranty is in lieu of all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for 
a particular purpose. Some states do not allow the disclaimer of implied warranty, so the preceding disclaimer may not apply. In states 
allowing only a partial limitation on implied warranties, the duration of implied warranties is expressly limited to the duration of the 
express warranty on the face hereof. In no event, whether as a result of breach of warranty or contract, tort (including negligence) 
strict liability or otherwise, shall CAP be liable of special, incidental, or consequential damages, including (but not limit ed to) loss of use 
of equipment or associated equipment, lost revenues, lost profits, cost of substitute equipment or cost of fuel or electricity.  
The above limitations shall inure to the benefit of CAP suppliers and sub-contractors. The above limitation on consequential damage 
shall not apply to injuries to persons in the case of consumer goods. Some states do not allow the exclusion or limitation of liability for 
consequential, or incidental damages, or for strict liability in tort, so the above exclusions and limitations may not apply. 
CAP does not assume or authorize any person to assume for CAP any other liability for the sale of CAP product. This warranty  gives you 
specific legal rights. You may also have other rights, which vary from state to state. 
The above warranty applies with respect to parts only and not labor. Accordingly, subject to the conditions and limitations set forth 
herein, the above warrant entitles the Customer only to receive a repaired or replacement part and not to the installation thereof. 
However, for the first one (1) year only of the above warranty period, CAP  will provide labor services to repair a Product or install 
repaired or replacement parts at its designated repair facilities, or at its option

, compensate its authorized dealers and authorized 

contractors at CAP’s standard fixed rates then in effect (irrespective of charges actually imposed and time actually expended) to 
provide such services                                                                                

                                                                                                                            

The above warranty is for repair or replacement only. Except to that limited extent, CAP will not under any circumstances be  liable for 
any loss, cost, damage, or expense of any kind arising out of a breach of this warranty or otherwise. Without intending to limit the 
foregoing sentence, it is specifically provided as follows: CAP SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, 
EXEMPLARY, SPECIAL, OR PUNITIVE DAMAGES, OR FOR ANY LOSS OF REVENUE, PROFIT OR USE, ARISING OUT OF A BREACH OF THIS 
WARRANTY (INCLUDING BUT NOT LIMITED TO DAMAGE RESULTING FROM CONDENSATE LEAKAGE) OR IN CONNECTION WITH THE 
SALE, MAINTENANCE, USE, OPERATION OR REPAIR OF ANY CAP PRODUCT. IN NO EVENT WILL CAP BE LIABLE FOR ANY AMOUNT 
GREATER THAN THE PURCHASE PRICE OF A DEFECTIVE PRODUCT.  

Warranty 07/21/11   

Summary of Contents for AHU































Reviews: