background image

(Moving) Viva! Welcome to Circusland! : Assembly Instructions

©

 Canon Inc. 

©

 Hideharu Naitoh & unity design

Assembly Instructions

Mountain fold(dotted line)

Make a mountain fold.

Valley fold(dashed and dotted line)

Make a valley fold.

Scissors line(solid line)

Cut along the line.

Cut in line(solid line)

Cut along the line.

 

Glue spot(Red dot)

Glue parts with the same number together.

Glue spot(Green dot)

Glue within the same part.

Glue spot(Blue dot)

Glue to the rear of the other part.

Glue

The glue spot(colored dot)

shows where to apply the glue.

Tools and materials

Assembly tip

Caution

Scissors, set square, glue(We recommend stick glue), pencil, used

ballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Before gluing, crease the paper along mountain fold and valley 

fold lines and make sure rounded sections are nice and stiff.

Glue, scissors and other tools may be dangerous to young children 

so be sure to keep them out of the reach of young children.

View of completed model

Assembly Instructions : Seven A4 sheets (No. 1 to No. 7)

*Hint: Trace along the folds with a ruler

  and an exhausted pen (no ink) to get a sharper, easier fold.

* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.

http://www.canon.com/c-park/en/

* Together with the circus animals, a dancing girl and 

   comical clowns welcome you to the circus when you 

   move the lever beneath the frame left and right.

Before starting assembly : Writing the number of each section on its back side 

before cutting out the sections is highly recommended.

(* This way, you can be sure which section is which even after cutting out 

the sections.)

Indicates where sections should 

be glued together.

Indicates where to insert sections. 

Do not glue the sections together.

Round bar : Use to give parts a curved surface.

Tweezers : Useful in working with fine parts.

Be sure to build this model 

carefully.

Glue the entire reverse sides of part 1 and 

part 4 to each other, as shown in this illustration.

Take care in positioning and direction of 

the parts when gluing them.

Caution :

 Spread the glue in a thin layer, 

              to prevent these parts from 

              warping after you glue them 

              together.

Glue part 2 to the remaining 

uncovered area of part 4.

Glue the rear sides of part 2 and part 3 

to each other, lining these parts up.

Summary of Contents for Viva! Welcome to Circusland!








Reviews: