External Dimensions
54 (2.13)
50.0 (1.97)
11.0 (0.43)
53.5 (2.11)
R23 (R0.91)
120 ( 4.72)
Unit : mm (in.)
3- 4.4 ( 0.17)
(mounting screw holes)
54.5 (2.15)
21.0 (0.83)
43.2 (1.70)
9.5 (0.37)
Connecting the Camera
Power Supply
See “Specifications” > “Others” > “Power Supply”.
Important
• Check with your dealer for more information about PoE devices.
• Some PoE devices allow current limits for each port, but applying
limits may interfere with performance. If using this type of PoE
device, do not limit the operating current.
• Some PoE devices have total consumption current limits for ports,
which can interfere with performance when multiple ports are in use.
For more information, check the instruction guide for your PoE device.
External Device I/O Terminals
External Device Input Terminals (IN)
The external device input terminal consists of a positive terminal (IN)
and negative terminal (GND). Connecting cables to the positive and
negative terminals and opening or closing the circuit notifies the Viewer.
Important
When connecting sensors and switches, use those that have terminals
which are isolated from internal power and GND.
External Device Output Terminals (OUT)
The external device output terminal consists of an OUT terminal and a GND
terminal. Controls from the viewer can be used to open and close the circuit
between the terminals. A MOSFET device is used for the output terminal.
Rating range for load connected to output terminals.
Rating between output terminals:
Maximum voltage 50 V DC
Continuous load current at or below 100 mA
On resistance: Below 1
Ω
Adaptive wiring for external device cables
Rating Range: (same for contact input and output)
Conductor Size: 0.42
–
0.80 mm ( 0.017
–
0.031 in.) dia.
(AWG: No. 26
–
20)
Stripped cable length should be approximately 11
–
13 mm (0.43
–
0.51 in.)
Note
• The External Device I/O Terminal consists of three terminals (IN, OUT,
and GND). The GND terminal serves as both the external device
input GND and the external device output GND.
• The GND terminal is connected to the camera interior GND.
• When using the external device input and output at the same time, couple
the GND wire from the input cable with the GND wire from the output
cable, conforming to the rating range, and connect it to the GND terminal.
• Do not push the external device I/O terminal button with too much force.
Doing so may cause the button to remain pushed-in.
IN
GND
OUT
GND
Input terminal
Output terminal
1 k
Ω
10 k
Ω
0.1 µF
10 k
Ω
Inter
nal contr
oller
Internal Connection Diagram
Audio Input Terminals
Camera has single audio input system supporting two types of microphone
input: LINE IN and MIC IN. Before use, change [Audio Input] on the Setting
Page (see “Operation Guide”). LINE IN is selected by default.
• Dynamic MIC IN
Input impedence: 20 k
Ω
–
40 k
Ω
• Condenser MIC IN
Input impedence (microphone bias resistance): 2.2 k
Ω
±20%
Microphone power supply: plug-in power (voltage: 2.3 V)
* Supported microphones: Condenser microphones with plug-in power support
• LINE IN
Input level: up to 1 Vp-p
* Use a microphone with an amplifier.
Specifications
Please refer to the installation procedures or “Operation Guide” for
specifications not listed below.
Camera
Lens
3.5x optical (4x digital zoom) zoom lens with
auto focus
Fixed focal length lens (4x digital zoom)
Viewing Angle
For 16:9 aspect ratios
Horizontal: 77.7° (W) – 20.7° (T)
Vertical: 40.4° (W) – 11.6° (T)
For 4:3 aspect ratios
Horizontal: 55.3° (W) – 15.5° (T)
Vertical: 40.4° (W) – 11.6° (T)
For 16:9 aspect ratios
Horizontal: 95.0°, Vertical: 60.0°
For 4:3 aspect ratios
Horizontal: 76.0°, Vertical: 60.0°
Pan Angle Range
350° (±175°)
Tilt Angle Range
90º (ceiling-mounted position: -90º – 0º)
When the horizontal direction of the camera is 0°
Rotation Angle Range
180° (±90°)
Interface
Network Terminal*
LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))
* LAN cables are category 5 or higher, with length 100 m
(328 ft.) or shorter.
Audio Input Terminal
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(common for LINE IN & MIC IN) LINE IN x 1 or MIC IN x 1
External Device I/O Terminal Input x 1, Output x 1
Memory Card
microSD Memory Card, microSDHC Memory Card,
microSDXC Memory Card compatible.
Others
Operating Environment Temperature: -10°C – +50°C (+14°F – +122°F)
Humidity: 5% – 85% (without condensation)
Storage Environment
Temperature: -30°C – +60°C (-22°F – +140°F)
Humidity: 5% – 90% (without condensation)
Installation Angle
±5° (camera) in relation to a horizontal plane
Power Supply
PoE: PoE power supply via LAN cable
(IEEE802.3af compliant)
Power Consumption
Max. 7.8 W
– Class 0 power sourcing equipment (requests 15.4 W)
Max. 7.6 W
– Class 0 power sourcing equipment (requests 15.4 W)
Max. 4.1 W
– Class 2 power sourcing equipment (requests 7.0 W)
Symbols Indicating Safety Precautions
This Installation Guide uses the following marks to indicate important
information the user should know in order to use the product safely.
In this section, explanations are provided for each mark so that
readers will understand the level of importance for each. Be sure to
observe these items.
Warning
Failure to follow the instructions
accompanied by this symbol may result in
death or serious injury.
Caution
Failure to follow the instructions accompanied
by this symbol may result in injury.
Caution
Failure to follow the instructions
accompanied by this symbol may result in
property damage.
Important
This symbol indicates important or
restricted items.
Note
Contains reference information for
operation or additional explanations.
Safety Precautions
Installation Precautions
Warning
Do not install in the following places:
• Places in strong direct sunlight, near heat-generating
objects, or subject to high temperatures
• Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.)
• Humid or dusty places
• Places subject to oily smoke or steam
• Places subject to sea air
• Confined or enclosed places
Fire or electric shock may result.
Precautions for the LAN (power) cable:
• Do not set any heavy objects on the LAN cable.
• Do not pull, forcibly bend, scratch, or modify the LAN cable.
Fire or electric shock may result.
Caution
For installation or inspection of this camera, consult the
dealer where you purchased the product.
• This installation should be made by a qualified service
person and should conform to all local codes.
• When installing on a ceiling, make sure the surface is
capable of withstanding the total weight of the camera, and
is sufficiently reinforced if necessary.
• Be sure to use installation screws designed for the type of
ceiling the camera is to be installed.
• Periodically check the parts and screws for rust and to
see if they have loosened, in order to prevent injuries and
equipment damage due to falling items.
• Do not install in unstable places, places subject to
significant vibration or impact, or places subject to salt
damage or corrosive gas.
• Be sure to attach the safety wire when installing the camera.
Failure to do so may result in the camera falling or other
accidents.
• Do not touch the edges of metal parts with bare hands.
• Be careful not to trap your fingers during installation of the
camera.
Injury may result.
Caution
•
Do not turn the camera rotator by hand.
•
Do not install on an unstable surface. Also, make
sure the camera is installed ±5°off horizontal.
• After turning off the power, do not turn the power on again
for at least 5 seconds.
• Take measures to remove static electricity before
performing any procedures
.
• If there is condensation, please wait to power on, until the
condensation dissipates.
Malfunction may result.
• Take care not to damage wiring or pipes in the room.
Damage to peripheral items may result.
Precautions for Use
Warning
• If you discover defective conditions such as smoke,
strange sounds, heat or strange odors, immediately stop
using the camera and contact your nearest dealer.
Fire or electric shock may result from continued use of the product.
• If thunder starts, stop installation or inspection etc. and do
not touch the camera or continue connecting the cable.
• Do not disassemble or modify the camera.
• Do not damage the connecting cable.
• Do not spill water or other liquid inside the camera, spray
the camera with water, or otherwise make it wet.
• Do not insert foreign objects into the camera.
• Do not use flammable sprays near the camera.
• Do not leave LAN cables connected when the camera is
not in use for long periods.
• Do not use flammable solvents such as alcohol, paint
thinner or benzine when cleaning the camera.
Fire or electric shock may result.
Only for European Union and EEA (Norway, Iceland and
Liechtenstein)
These symbols indicate that this product is
not to be disposed of with your household
waste, according to the WEEE Directive
(2012/19/EU), the Battery Directive
(2006/66/EC) and/or national legislation
implementing those Directives.
If a chemical symbol is printed beneath the symbol shown
above, in accordance with the Battery Directive, this indicates
that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead)
is present in this battery or accumulator at a concentration
above an applicable threshold specified in the Battery
Directive.
This product should be handed over to a designated collection
point, e.g., on an authorized one-for-one basis when you buy
a new similar product or to an authorized collection site for
recycling waste electrical and electronic equipment (EEE) and
batteries and accumulators. Improper handling of this type of
waste could have a possible impact on the environment and
human health due to potentially hazardous substances that are
generally associated with EEE. Your cooperation in the correct
disposal of this product will contribute to the effective usage of
natural resources.
For more information about the recycling of this product, please
contact your local city office, waste authority, approved scheme
or your household waste disposal service or visit www.canon-
europe.com/weee, or www.canon-europe.com/battery.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
