Canon Satera LBP-3700 User Manual Download Page 114

Page: 114 / 114

113

• How To Set the Top Rear Cover

If the top rear cover comes off or is not set properly, take the cover out
once using the following procedure, and then set it again, properly.

Fit up the upper left portion of the top
rear cover

, then insert the projection

on the upper right into the hole

2. Set the top rear cover.

While pressing the tabs on the back of
the top rear cover

, insert the tabs into

the holes

to set the top rear cover.

1. While pressing the top rear cover from both sides

and pressing the

tabs on the top rear cover

, remove the top rear cover

The top rear cover is set, snapping. Make sure that the tabs are inserted completely into the
holes.

Film

Be sure that the film of the top rear cover does not get
creased when installing the top rear cover.

IMPORTANT

Summary of Contents for Satera LBP-3700



















































































































Search results

Summary of Contents for Satera LBP-3700

Reviews:

Related manuals for Satera LBP-3700

Brands by name

Popular brands

Canon Satera LBP-3700, User Manual

Search results

Summary of Contents for Satera LBP-3700

Reviews:

Related manuals for Satera LBP-3700

Brands by name

Popular brands