No ink (no raw ink).
[1698] U172 The ink has run out. Stop
printing, then
replace the ink tank.
(Applicable ink tank icon)
The PGI-9PBK, PGI-9Y, PGI-9M, or PGI-9C ink is used
up (the applicable ink tank LED flashes). Press the
Stop/Reset button to stop printing, replace the empty ink
tank(s), then resume printing.
To prevent faulty printing such as ink mixture, the error is
indicated and printing is stopped when the remaining ink
amount in the ink tank becomes lower than the amount
required to maintain the print quality.
Unknown ink.
[1689] U181 The ink has run out. Stop
printing, then
replace the ink tank.
The PGI-7BK ink is detected to be used up (the ink tank
LED flashes). Stop printing, replace the ink tank, then
resume printing. The ink tank must be replaced before
resuming printing.
An ink tank which has once been empty is installed.
Printing with a once-empty ink tank can cause faulty
printing such as improper ink mixture, or it can damage
the machine. To continue printing without replacing the
ink tank, press the Stop/Reset button for 5 sec. or longer
to disable the function to detect the remaining ink amount.
After the operation, it is recorded in the machine that the
function to detect the remaining ink amount was disabled.
Unknown ink.
[1699] U182 The ink has run out. Stop
printing, then
replace the ink tank.
(Applicable ink tank icon)
The PGI-9PBK, PGI-9Y, PGI-9M, or PGI-9C ink is
detected to be used up (the applicable ink tank LED
flashes). Stop printing, replace the ink tank, then resume
printing. The ink tank must be replaced before resuming
printing.
An ink tank which has once been empty is installed.
Printing with a once-empty ink tank can cause faulty
printing such as improper ink mixture, or it can damage
the machine. To continue printing without replacing the
ink tank(s), press the Stop/Reset button for 5 sec. or
longer to disable the function to detect the remaining ink
amount. After the operation, it is recorded in the machine
that the function to detect the remaining ink amount was
disabled.
Non-supported hub.
[2002]
---
An unsupported USB hub is
connected. Remove the hub.
Remove the applicable USB hub from the PictBridge
(USB) connector.
No paper in the
ADF,
Paper jam in the
ADF,
Non-supported length
of paper in the ADF
(too long or too
short).
---
---
1. Press the Stop./Reset button.
2. Except the document page stuck in the ADF, remove
all the other pages from the ADF, and open the
document feeder cover.
3. Raise the lever to release the paper, and pull out the
stuck paper from under the pick-up roller to the
document feeder cover side.
4. Pull out the stuck paper from the ADF.
5. Lower the lever, and close the document feeder cover.
Document in ADF. Redo
operation after
checking document in ADF
and pressing [OK].
The document is jammed in the ADF. Remove the
jammed document, press the OK button, then perform the
operation again.
Document size is too long.
Redo operation after checking
document on ADF and
pressing [OK].
The document page is too long, or it is jammed in the
ADF. Remove the document from the ADF, and press the
OK button to clear the error. Confirm that the document
length is supported, and perform the operation again.
7 / 65
Summary of Contents for PIXMA MX7600
