Canon Pixma G1000 series Service Manual Download | Manualshive

Page: 19 / 80

background image

(19/80)

QY8-13EX-040

(3) Removing the Document Cover.

1) Remove the right and left bosses, then detach the document cover.

(4) Removing the Rear Cover

1) Remove two screws to detach the rear cover.

(5) Removing the Absorber Kit (Partial)

1) Remove the two sheets of absorber kit (partial).

Note: Set the ink absorber counter value to 30% after the partial replacement.

See

3-3 (4) Ink absorber counter setting

for details.

easyfixs.blogspot.com

«
...
17
18
19
20
21
...
»

Summary of Contents for Pixma G1000 series

















































































Reviews:

No comments

Related manuals for Pixma G1000 series

Pixma MG2400 Series

Brand: Canon Pages: 2

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 48

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

imageRUNNER C3125i

Brand: Canon Pages: 816

ImageCLASS MF4570dw

Brand: Canon Pages: 164

imagePRESS C800 Series

Brand: Canon Pages: 132

ImageCLASS MF5730

Brand: Canon Pages: 2

Brand: Canon Pages: 11

Brand: Canon Pages: 2

Brand: Canon Pages: 12

PIXMA Pro9000 Mark II Series

Brand: Canon Pages: 4

Aficio MP C6503SP

Brand: Ricoh Pages: 264

Brand: BIXOLON Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands