Canon imagePROGRAF TX-4000 Online Manual Download Page 494 | Manualshive

Page: 494 / 1033

background image

Regulatory Information

Lithium Battery

• Dispose of used batteries according to the local regulations.
• Risk of explosion if battery is replaced by an incorrect type.

Users in the U.S.A.

FCC Notice (U.S.A. Only)
For 120V, 60Hz model
Model Number: K10475 (Contains FCC Approved WLAN Module K30357)
Optional parts: Roll Unit RU-42

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of a shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If
such changes or modifications should be made, you could be required to stop operation of the equipment.

FCC ID:AZDK30357

Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The equipment complies with FCC radiation exposure limits for at uncontrolled equipment. This
equipment should be installed and operated with minimum distance at least 20cm between the radiator
and persons body (excluding extremities: hands, wrists, feet and ankles) and must not be colocated or
operated with any other antenna or transmitter.

Canon U.S.A., Inc.
One Canon Park

494

«
...
492
493
494
495
496
...
»

Summary of Contents for imagePROGRAF TX-4000










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for imagePROGRAF TX-4000

Brand: Canon Pages: 29

PIXMA MX410 Series

Brand: Canon Pages: 46

Brand: Canon Pages: 65

Brand: Canon Pages: 4

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Sure shot 80 tele

Brand: Canon Pages: 39

BJC6500 - BJC 6500 Color Inkjet Printer

Brand: Canon Pages: 6

Brand: Canon Pages: 20

imagePROGRAF iPF6450

Brand: Canon Pages: 35

PIXMA MX340 Series

Brand: Canon Pages: 11

PIXMA MX340 Series

Brand: Canon Pages: 16

imagePROGRAF iPF6300S

Brand: Canon Pages: 12

Brand: Canon Pages: 19

Brand: Canon Pages: 101

iP4700 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 28

Brand: Canon Pages: 2

Brand: Canon Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands