Canon imageFORMULA DR-G2140 Service Manual Download Page 95

Page: 95 / 196

3-33

CHAPTER 3 DISASSEMBLY & REASSEMBLY

10. Pull-in Lower Roller

1) Remove the right and left covers.

(Page 3-3)

(Page 3-5)

2) Remove the lower entrance guide.

(Page 3-31)

3) Remove the left front belt,

(Page 3-32)

4) For the pull-in lower roller



, remove the

stopper



, pulley



and pin



on the left

side. And remove the stopper



on the

right side, and bearing



on each side.

And remove the roller.

Note:

Do not lose the pin.

Figure 3-614

11. Registration Lower Roller

1) Remove the right and left covers.

(Page 3-3)

(Page 3-5)

2) Remove the right belt and left front belt.

(Page 3-31)

(Page 3-32)

3) Remove the lower entrance guide.

(Page 3-31)

4) Remove 2 screws



(M3, stepped 3.2),

and remove the lower feed guide



Figure 3-615

5) For the registration lower roller



, remove

the stopper



, pulley



and pin



each side. And remove the bearing



each side. And remove the roller.

Note:

Do not lose the pin.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 95 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: