Canon imageFORMULA DR-G2140 Service Manual Download Page 94

Page: 94 / 196

3-32

CHAPTER 3 DISASSEMBLY & REASSEMBLY

8. Left Front Belt

1) Remove the left cover.

(Page 3-5)

2) Loosen the screw



(M3-bind head,

round tip) of the tension plate



. And re-

move the coil spring



and the belt



Figure 3-612



Notes on assembling

First, assemble the belt to the pulleys, and

then tighten the screw. The tension of the

belt is fixed by a coil spring with the tension

plate.

9. Left Rear Belt

1) Remove the left cover.

(Page 3-5)

2) Loosen the screw



(M3-bind head,

round tip) of the tension plate



. And re-

move the belt



Figure 3-613



Notes on assembling

Verify the orientation of the flange attached

to the pulley. "

" indicated by mark



the above figure shows the position of the

black pulley (the flange is inside).

First, assemble the belt to the pulleys, and

then tighten the screw. The tension of the

belt is fixed by a coil spring with the tension

plate.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 94 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: