Canon imageFormula DR-6010C User Manual Download

Page: 20 / 142

Chapter 2

Setup

2-5

Software Installation

Install the software before connecting the scanner to the computer.

Log onto Windows with an account that has Administrator privileges.

IMPORTANT

• Be sure to log on as an Administrator.

• Close all other applications before installing the software.

Insert the DR-6010C Setup disc into the PC’s CD-ROM drive.

The menu screen appears automatically when you insert the CD-ROM into the CD-ROM

drive. If the setup wizard does not start up, execute setup.exe in the CD-ROM.

Click [Typical Installation].

The [Typical Installation] screen appears.

Note

• When you select [Typical Installation], all of the displayed software and the User Manual will

be installed automatically. If you want to reinstall only specific software that you have

previously uninstalled, select [Custom Installation] and specify the software.

• The DR-6010C driver installation comprises the Scanner Driver and Job Tool installation.

Menu Screen

Summary of Contents for imageFormula DR-6010C















































































































































Search results

Summary of Contents for imageFormula DR-6010C

Reviews:

Related manuals for imageFormula DR-6010C

Brands by name

Popular brands

Canon imageFormula DR-6010C, User Manual

Search results

Summary of Contents for imageFormula DR-6010C

Reviews:

Related manuals for imageFormula DR-6010C

Brands by name

Popular brands