manualshive.com logo in svg

Canon i-SENSYS MF4120, Service Manual

Share
Download
Canon i-SENSYS MF4120 Service Manual Download Page 117

Chapter 12

12-3

00B8

Remote side disconnect after our side sending DCS signal in V.34.

00BA

Cannot received correct signal after our side sending DTC signal in V.34.

00BB

Every time our side received DIS signal after sending DTC in V.34.

00BC

Modem can't ready within 10 second after entering primary channel in V.34.

00BD

Can't detect correct V.21 or JM signal after detected FSK frequency.

00BE

Remote side no document to be polled after V.8 handshaking.

00BF

Capability no match after V.8 handshaking

00C1

At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from receiving unit.

00C2

Remote side disconnect after sending out V.8 CM signal.

00C4

After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN.

00C5

Received DCN signal after sending MPS signal.

00C9

At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit.

00CA

After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN, RTP.

00CB

After sending EOP signal, the received is DCN signal.

00CF

Received incorrect signal after sending DTC signal for V.34 polling.

00D0

Received ERR signal after sending EOR_NULL.

00D1

Received incorrect response after sending PPS_EOP signal

00D2

Received DCN after sending PPS_EOP signal

00D3

Received DCN after sending PPS_NULL signal

00D8

Can't detect correct phase 3 signal for poling.

00D9

Can't detect correct phase 3 signal after detect silence after phase 2.

00DA

Can't detect phase 4 signal within 30 sec.

00DB

Can't received any T.30 signal within 30 sec within phase 4.

00DC

Received T.30 signal in phase 4 other than DCS, DIS or DTC

00DE

Remote side no SUB capability.

00E0

At phase-D, transmitting units out PPS_NULL 3 times consecutively but receive not answer.

00E1

Received incorrect response after sending PPS_NULL.

00E2

Can't receive any response in RR response procedure after sending PPS_NULL.

00E4

At phase D, transmitting units out PPS_MPS 3 times consecutivery but receive no answer.

00E5

Received incorrect response after sending PPS_MPS signal

00E6

Can't receive any response in RR response procedure after sending PPS_MPS.

00E7

Reseived DCN after sending PPS_MPS.

00E8

At phase-D, transmitting units out PPS_EOP 3 times consecutively but receive no answer.

00E9

Receive PIN signal after sent last page data.

00EA

Can't receive any response in RR response procedure after sending PPS_EOP.

00EE

At phase-D, transmitting units out EOR_NULL 3 times consecutively but receive no answer.

00EF

Received incorrect response after sending EOR_NULL. 

00F0

Can't receive any response in RR response procedure after sending EOR_NULL.

00F1

At phasa-D, transmitting units out EOR_MPS 3 times consecutively but receive no answer.

00F2

Received incorrect response after sending EOR_MPS.

00F3

Received ERR signal after sending EOR_MPS.

00F4

Can't receive any response in RR response procedure after sending EOR_MPS.

00F5

At phasa-D, transmitting units out EOR_EOP 3 times consecutively but receive no answer.

00F6

Received incorrect response after sending EOR_EOP

00F7

After Received ERR, our side can't received response after sending EOR_EOP command.

00FC

Can't receive any response after sending CTC.

00FD

Can't speed down to lower speed.

00FE

Memory full for transmission

00FF

REDAIL ALL FAIL

Error Code

Description

Summary of Contents for i-SENSYS MF4120













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands