manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 118

Print with or without winding

Winding options

Introduction

For the Colorado 1630 there are several winding options depending on the type of media you are
using.

NOTE

It is very important to select the correct winding option. If you choose the wrong option this can

lead to print quality and winding issues.

Overview

In a media profile a media category is used that corresponds with the loaded media type. Each
media category uses default media settings. One of the media settings is [Winding tension] that
controls the winding tension that best fits the media type.

For more information, see 

Change the media settings on page 67

.

Options

Media category

[Winding ten‐
sion] value

Media characteristics

Print and wind with-
out a tension bar on
page 119
Print without winding
on page 131
AutoCut on page 149

Polymeric & cast vinyl
Monomeric vinyl
Film
Light paper
Paper

[no tension bar]

The media can be transpor-
ted well and is not too
weak.

Print and wind with a
tension bar on
page 122

Heavy banner
Light banner
Textile
Canvas

[tension bar]

The media is weaker and
sensitive for buckling, but
not too stiff.

Print and wind with a
locked tension bar on
page 127

Thick film
Heavy paper

[locked tension
bar]

The media is stiff.

Print with or without winding

118

Chapter 4 - Handle the media

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands