Canon Arizona 1300 Series User Manual Download Page 193 | Manualshive

Page: 193 / 248

background image

Clean the Carriage Underside

Introduction

The underside of the carriage must be cleaned daily. It may be necessary to clean it more
frequently if any of the following conditions exist:
• media has a high level of static charge
• full bleed printing
• media thickness value is incorrect (carriage is too high)

Equipment

• Isopropyl alcohol (IPA)
• Cloth-Poly Wipe 10cm x 10cm (lint-free)

IMPORTANT

When you clean the carriage underside you may need a light to evaluate its condition. Do not

use a LED or Halogen (flashlight, smart phone etc). LED and Halogen light sources will cure the

UV-based ink in the printhead nozzles rendering it useless. Use fluorescent bulbs or cover your

light source with silicon glass or quartz..

Procedure

1.

Slide the maintenance station drawer open.

2.

Push the raise carriage button.

3.

Fold a lint-free poly wipe cloth to a size that will fit between the printheads on the bottom of the
carriage.

4.

Dip the cloth in isopropyl alcohol.

5.

Clean the ink from the bottom of the carriage.

IMPORTANT

Avoid touching the printheads.

Clean the Carriage Underside

Chapter 11 - Maintenance

193

«
...
191
192
193
194
195
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

KXPX2M - HOME PHOTO PRINTER

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 9

Jetwriter KX-CL500

Brand: Panasonic Pages: 32

Brand: Oki Pages: 1

imageRUNNER 5075

Brand: Canon Pages: 502

imageRUNNER 5075

Brand: Cannon Pages: 268

imageRUNNER 4570

Brand: Canon Pages: 154

Brand: Olivetti Pages: 438

da Vinci 1.0 Pro

Brand: XYZ Printing Pages: 11

Aficio MP C6503SP

Brand: Ricoh Pages: 264

7400DT - Phaser Color LED Printer

Brand: Xerox Pages: 20

Brand: SEH Pages: 50

WorkCentre 7655

Brand: Xerox Pages: 19

Brand: Kyocera Pages: 28

Brand: Seiko Epson Pages: 301

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands