Canon Arizona 1300 Series User Manual Download Page 166 | Manualshive

Page: 166 / 248

background image

Varnish QuickStart

Introduction

This section shows you how to print a simple job with a varnish Printer Flood Fill. The following
section provides more detail about printing with varnish.

Purpose

This exercise will help you get familiar with some of the basic concepts involved when you print
images with varnish.

Printing varnish requires an ONYX media profile (media model) that was made with a CMYKSS
ink configuration with spot colours defined. All print modes are supported except the High
Definition print mode.

Before you begin

Import an ONYX media profile that was made using a CMYKSS ink configuration with 2 spots
defined.

NOTE

Sample Media models for varnish are available for download from the Customer Support
section of our website: https://dgs.cpp.canon. These media models are documented later in this
chapter (see How to Use Media Models to Print with White Ink or Varnish).

How to Print a Simple Job Using Varnish

Procedure

1.

Open an image of your choice using an ONYX media profile that supports spot data (CMYKSS ink
configuration with spot colours).

2.

Take the printer offline in ONYX RIP-Queue so the job will not be automatically sent to the printer.

3.

Process/rip the job.

4.

Define a printer flood coat.
To set up a varnish printer flood, modify the printer settings of a processed job in RIP Queue -
right click the job, edit printer settings, then select Print Varnish With: Flood Coat (Printer).

Varnish QuickStart

166

Chapter 9 - Manage a White Ink Workflow

«
...
164
165
166
167
168
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Brand: QMS Pages: 160

Brand: QMS Pages: 110

Brand: QMS Pages: 158

Brand: CAB Pages: 144

ImageCLASS MF3240 Series

Brand: Canon Pages: 62

ImageCLASS MF4270

Brand: Canon Pages: 226

imageCLASS D660

Brand: Canon Pages: 8

ImageCLASS MF3240 Series

Brand: Canon Pages: 136

Color imageRUNNER C5180 Series

Brand: Canon Pages: 851

imageCLASS D320

Brand: Canon Pages: 121

imageCLASS MF212w

Brand: Canon Pages: 236

imageCLASS D760

Brand: Canon Pages: 82

imageclass LBP251dw

Brand: Canon Pages: 72

ImageCLASS MF4270

Brand: Canon Pages: 248

ImageCLASS MF4270

Brand: Canon Pages: 36

imageCLASS D760

Brand: Canon Pages: 8

imageCLASS MF4100 Series

Brand: Canon Pages: 140

imageclass LBP251dw

Brand: Canon Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands