Canon Arizona 1300 Series User Manual Download Page 126

Page: 126 / 248

Operator Guidelines for White Ink

Introduction

This chapter is necessary only if your printer has the white ink option.

Managing White Ink

White ink is re-circulated in the system to limit any settling of the ink. For this to take place,

the

printer must be left powered on at all times

. Regular maintenance is required to keep the white

printheads functioning properly. This may involve additional purge cycles.

Before you begin

If your printer includes the white ink option, a white ink bag must be present in order for the
printer to function properly.

IMPORTANT

Daily maintenance is important even when white ink is not being actively used. Failure to

perform daily maintenance can result in nozzle dropouts. The purpose of maintenance is to clean

the nozzles of the printheads and thus ensure better image quality.

Procedure

Agitate the white ink bag gently once a day.

Perform Printhead Maintenance for white even if the printer is not used that day.

NOTE

Refer to the Printhead Maintenance section of the Maintenance chapter for an
explanation of how to perform daily maintenance.

Operator Guidelines for White Ink

126

Chapter 9 - Manage a White Ink Workflow

Summary of Contents for Arizona 1300 Series

























































































































































































































































Search results

Summary of Contents for Arizona 1300 Series

Reviews:

Related manuals for Arizona 1300 Series

Brands by name

Popular brands

Canon Arizona 1300 Series, User Manual

Search results

Summary of Contents for Arizona 1300 Series

Reviews:

Related manuals for Arizona 1300 Series

Brands by name

Popular brands